background image

P. 2

 Installation 

Guide

 AS-2510 TW

Table of Contents 

Table of Contents .....................................2 
Introduction ...............................................2 
Included in the Kit .....................................2 
Installation Points to Remember...............3 
Harness Description .................................4 
Flashing the Hood Pin Switch...................9 
Tip.............................................................9 
Remember:...............................................9 
The Programming Assistance Button .....10 
Caution ...................................................10 
Programming a Transmitter ....................10 
Before you Proceed ................................10 
The Transmitter Programming procedure10 
Entering Programming Options Mode ....10 
Programming Options.............................11 
Tach Programming .................................13 
About Tach Programming.......................13 
Multi-speed Tach Programming..............13 
Automatic Tach Programming ................14 
Horn Chirp Timing...................................14 

Testing.................................................... 14 
Closing Up.............................................. 15 
Supplementary Information .................... 16 
Fifth Relay Output (2

nd

 IGN, ACC or 

CRANK).................................................. 16 
Caution! .................................................. 16 
Ignition-controlled Door Locks................ 16 
Secure Lock ........................................... 16 
Standard Secure Lock............................ 16 
Smart Secure Lock................................. 17 
Lock Pulse Duration ............................... 17 
Engine Run Time.................................... 17 
Starter Kill (Installation) .......................... 17 
Passive or Active Arming ....................... 17 
Resetting the Remote Car Starter .......... 17 
Events Logging....................................... 18 
Events playback ..................................... 18 
Start Failure Codes through the Parking 
Lights...................................................... 18 
Diagnostics – Parking Light Flash Table 19 

Introduction 

This Guide contains all the information relevant and necessary for the installation of the 
Remote Car Starter. Most of the features of this product are explained in the 

User Guide

.

Therefore, if you need detailed information about a feature of the product, we recommend 
that you refer to the User Guide. 

Included in the Kit 

Please carefully read the Installation Guide before beginning the installation, especially the 

Harness Description 

section and the 

Programming Options

.

It is very important that you 

familiarize yourself with the programming and the operation 

of the Remote Car Starter

, even if you have already installed a similar Remote Car Starter 

in the past. There are many innovative features that you may overlook if you do not read this 
Guide.  
Prior to the installation, make sure that all the hardware components required to install the 
system are in the box. 

The following is a list of components included in the kit: 

x

1  – Remote Car Starter Control Unit 

x

1  – FM  long-range Transceiver  

x

1  – multi-channel 5-button Remote Control 

x

1  – plug-in L.E.D. 

x

1  – six-pin 14 AWG Harness (Ignition Harness) 

x

1  – five-pin 18 AWG Harness (Main Harness) 

x

1  – twelve-pin 22 AWG Harness (Accessories Harness) 

Summary of Contents for AS-2510 TW




















Reviews: