2013/05/29
RS-777 OP REV 1D
10
1.Under ignition on press
F
button four times while “
CAR JACK”
flash on text area(see Table 1), then
press
button for 2 seconds to activate Anti Car-Jacking mode or
Under ignition on press and hold the
and
buttons at the same time for 2 seconds. The parking
lights will turn on for 1.5 seconds to indicate the system enter the anti car-jacking mode.
2.Once the system in anti car-jacking mode, the system will be triggered when the door is opened and
closed while the ignition is “ON”.
PASSIVE ANTI CAR- JACKING:
It will operate as noted below:
1. Turn the ignition switch to the “ON” position and the system will arm.
2. Once the system is armed, if you are forced from the vehicle, the system will trigger when the door is opened and
closed while the ignition is “ON”.
TRIGGER THE ANTI CAR -JACKING MODE:
a). 50 seconds after the system has beer triggered. The siren will start chirping for 15 seconds.
b). During this 15 second period of chirping, you will be alerted to push the valet switch once to turn off the
car-jacking feature. If not, it will enter a second timer for car jacking.
c). 65 seconds after the system has been triggered, the siren will start sounding and the parking lights will start
flashing.
d). 90 seconds after the system has been triggered,
1. The siren will sound and the parking lights will flash, and
2. The starter disable will activate to prevent the vehicle from starting.
3. It will remain active until the vehicle's battery power is exhausted.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system
disarmed
Note: If you use password pin code to double protect the vehicle security, you will need to use it to completely disarm
the system.
N. SYSTEM’S TRIGGER CHECK
(For two-way transceiver operation only)
By Table – 2, press and hold
F
button of LCD remote until 2 beeps heard, release and re-press
F
button 2
more times, the LCD display show “ALARM CHECK “ on text field (see Table 2), then press
button to
activate system trigger check.
Note: If it has no response then you are out of range.
O. SYSTEM’S STATUS CHECK
(For two-way transceiver operation only)
By Table – 2 press and hold
F
button of LCD remote until 2 beeps heard, release and re-press
F
button
one more time, the LCD display show “STATUS CHECK “ on text field (see Table 2) then press
button to activate system status check.
Note: If it has no response then you are out of range.
P. DRIVER PAGING / LOSE & FOUND (
For two-way transceiver operation only)
It is useful the event that someone wants to page the driver of the parked vehicle or someone cannot find
his LCD remote transceiver.
Under the ignition switch “off” condition, press and hold the valet switch for
3
seconds to page the driver,
one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from
you Remote LCD transceiver.
Q.
DOME LIGHT CONVENIENCE SUPERVISION (Optional Feature)
The alarm has a unique feature that will turn on your vehicle dome light as follows:
1. Upon disarming, the interior light will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: Turning on the ignition switch or arming the alarm will turn off the dome light.
R.
IGNITION CONTROL DOOR LOCK/UNLOCK. (Programmable Feature)
If the vehicles door locks have been interfaced to the security system, the system will automatically lock the vehicle's
doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”. (Default
is “OFF”)
S. TRUNK RELEASE (CHANNEL 3) OUTPUT.
Press and hold
button on the transmitter for two seconds to remote control the trunk release or other
electric devices.
T.
CHANNEL 4 TIMER CONTROL OUTPUT
By Table – 1, Press and hold
F
button of LCD remote until 1 beep sound , release and re-press
F
button 3
more times the LCD display show “CH 4“ on text field (see Table 1) then press
button to activate
channel 4 function. Or press remote
transmitter
and
buttons at the same time to active Channel 4
function.
Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal for any
time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight,
power window or sunroof. (Factory defaults setting at
1 sec. pulse
output.)
