-|Transparent Guide|-
TCD210158AB
Refrigeration Temperature
Controllers
TC3YF Series
PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction
manual, other manuals and Autonics website.
The specifications, dimensions, etc are subject to change without notice for product
improvement Some models may be discontinued without notice.
ᜧ ᜣ ᜫ
Features
• ON/OFF control
•
Standard input type : thermistor (NTC)
- RTD(Pt100Ω) input models available upon request.
• Temperature range
- Thermistor (NTC) : -40.0 to 99.9 ℃ (-40 to 212 ℉)
- RTD (Pt100 Ω) : -99.9 to 99.9 ℃ (-148 to 212 ℉)
•
Various functions available for optimal cooling control
- Auto/manual defrost selection, compressor start-up delay, restart delay, minimum
ON time, end-defrost delay, evaporator fan operation delay
• Input correction function
•
Operation cycle programming available to protect contents in case of error
•
Follow instructions in ‘Cautions during Use’. Otherwise, it may cause unexpected
accidents.
•
Check the polarity of the terminals before wiring the temperature sensor. For RTD
temperature sensor, wire it as 3-wire type, using cables in same thickness and length.
For thermocouple (CT) temperature sensor, use the designated compensation wire for
extending wire.
•
Keep away from high voltage lines or power lines to prevent inductive noise. In case
installing power line and input signal line closely, use line filter or varistor at power line
and shielded wire at input signal line. Do not use near the equipment which generates
strong magnetic force or high frequency noise.
•
Install a power switch or circuit breaker in the easily accessible place for supplying or
disconnecting the power.
•
Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature
controller.
•
12-24 VDCᜡ
p
ower supply should be insulated and limited voltage/current or Class 2,
SELV power supply device.
•
Make a required space around the unit for radiation of heat. For accurate temperature
measurement, warm up the unit over 20 min after turning on the power.
Safety Considerations
•
Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards.
•
symbol indicates caution due to special circumstances in which hazards may occur.
Warning
Failure to follow instructions may result in serious injury or death
01.
Fail-safe device must be installed when using the unit with machinery that
may cause serious injury or substantial economic loss.(e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
02.
Do not use the unit in the place where flammable/explosive/corrosive gas,
high humidity, direct sunlight, radiant heat, vibration, impact or salinity
may be present.
Failure to follow this instruction may result in explosion or fire.
03.
Install on a device panel to use.
Failure to follow this instruction may result in electric shock.
04.
Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire or electric shock.
05.
Check ‘Connections’ before wiring.
Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.
Caution
Failure to follow instructions may result in injury or product damage
01.
When connecting the power input and relay output, use AWG 28 to 12 (0.50
mm
2
) cable or over and tighten the terminal screw with a tightening torque
of 0.3 to 0.4 N m.
When connecting the sensor input without dedicated cable, use AWG 28 to
16 cable and tighten the terminal screw with a tightening torque of 0.3 to 0.4
N m.
Failure to follow this instruction may result in fire or malfunction due to contact
failure.
02.
Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage
03.
Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
04.
Keep the product away from metal chip, dust, and wire residue which flow
into the unit.
Failure to follow this instruction may result in fire or product damage.
Cautions during Use
