2
www.AutomationDirect.com
1-800-633-0405
CUT AWAY
VIEW
MAXIMUM ALLOWABLE
PANEL THICKNESS
Mounting Clip Installation:
Cable Connections:
2. Install Monitor through Enclosure Door or Wall:
• The monitor must be installed on a flat surface of a NEMA type 1, 4, 4X
or 12 enclosure.
• Use dimensions as shown in the diagram below to provide a rectangular
mounting cutout in an approved NEMA 4/12 enclosure’s door or wall.
• Mount the monitor through the enclosure cutout, install and tighten (14)
mounting clips to a torque of 8.0 inch-pounds as shown in the diagram
to the right
Cutout Dimensions:
Model
A
B
ATM1500 / ATM1500T
12.00”
(304.8 mm)
15.00”
(381.0 mm)
ATM1700 / ATM1700T
13.70”
(348.0 mm)
16.35”
(415.3 mm)
ATM1900 / ATM1900T
14.90”
(378.5 mm)
17.75”
(450.9 mm)
CUTOUT
A
B
WARNING: An operating temperature of 0 to 50 °C (32 to 122 °F)
ambient termperature inside the enclosure needs to be maintained
for proper operation of the monitor.
WARNING: Suitable for use in Class 1, Division 2 Groups A, B, C,
and D; Class 2 Division 2 Groups F and G, Class III hazardous locations,
or non-hazardous locations only.
3. Connect DVI or VGA Video Cable between Monitor & PC
• Connect the included 10’ VGA video cable from the video connector on the
monitor to the video output connector on the host PC being used with the mon-
itor or use a digital DVI cable (sold separately).
• If using a DVI cable, input selection must be changed to DVI by pushing the UP
button on the rear of the monitor.
N
ote
: t
he
15”
MoNitor
will
prodUct
the
best
iMAGe
qUAlity
if
the
pc
is
set
for
A
1024
x
768
pixels
@
either
60, 70
or
75
h
z
.
video
Mode
.
N
ote
: t
he
17”
ANd
19”
MoNitors
will
prodUce
the
best
iMAGe
qUAlity
if
the
pc
is
set
for
A
1280
x
1024
pixels
@
either
60
or
75 h
z
.
video
Mode
.
4. Connect USB or Serial Cable between Monitor and PC
• Applies to touch screen version only.
• Use either the included 10’ RS-232 Serial touch screen cable or the 10’ USB touch
screen cable from the appropriate connector on the monitor to the appropriate
connector on the host computer; do not connect both.
• If using the USB cable, secure the cable using the included USB retention bracket
and screw; consult the Hardware User’s Guide, ATM-USER.
N
ote
: w
heN
UsiNG
the
Usb
toUchscreeN
coNNectioN
,
the
Use
of
the
Usb
reteNtioN
brAcket
is
reqUired
for
hAzArdoUs
lo
-
cAtioNs
ANd
hiGhly
recoMMeNded
for
NoNhAzArdoUs
locAtioNs
WARNING: Damage can occur by applying excessive torque to the
mounting clips.
* NOTE: USE ONE OR THE
OTHER, NOT BOTH.
TOUCH SCREEN
CABLES *
VIDEO CABLE *
DISPLAY POWER
WARNING
Touch Screen is still
active while display
power is off
WARNING - EXPLOSION HAZARD: Do not connect or disconnect the USB
ports unless the power has been switched off or the area is known to
be non-hazardous.
AVERTISSEMENT - RISQUE D’EXPLOSION - Ne pas brancher ou débrancher
le ports USB á moins que l’alimentation á été coupée ou si la zone n’est
pas hazardeuse.
ADVERTENCIA - PELIGRO DE EXPLOSIÓN - No conecte o desconecte los
puertos USB a menos que la computadora se encuentre apagada o el
área se considere no peligrosa.
WARNUNG - EXPLOSIONSGEFAHR - USB-Ports nur anschließen oder
trennen, wenn keine spannung anliegt oder der Bereich nicht
explosiongefährdet ist.
N
ote
: t
o
preveNt
iNAdverteNt
discoNNectioN
of
video
ANd
/
or
seriAl
toUchscreeN
cAbles
,
AssUre
thAt
the
thUMbscrews
Are
sUfficieNtly
tiGht
.
