Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual Download Page 10

10

www.automationdirect.com/click-plc

3505 HUTCHINSON ROAD 

CUMMING, GA 30040-5860 

1-800-633-0405

C2-02CPU Quick Start Guide 

Copyright© 2020, 

Automationdirect.com

 Incorporated/All Rights Reserved Worldwide

FCC and ISED Regulatory Statements

The C2-02CPU has achieved modular radio certification on 
a reference design for the United States and Canada . The 
reference design has been certified for Part 15.247 (Intentional 
Radiator) of the FCC rules and regulations, Industry Canada 
RSS-210.

Per FCC 15.19(a)(3) and (a)(4) This device complies with 
part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions: (1) This device may not cause harmful 
interference, and (2) this device must accept any interference 
received, including interference that may cause undesired 
operation.

Note: This equipment has been tested and found to comply 
with the limits for a Class A digital device, pursuant to part 
15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the 
equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in which case the 
user will be required to correct the interference at his own 
expense.

The C2-02CPU complies with Part 15.247 modular (Inten-
tional Radiator) FCC rules and regulations. Changes or mod-
ifications not expressly approved by AutomationDirect could 
void the user’s authority to operate the equipment. 

Per RSS-Gen, Section 8.4 this device complies with Industry 
Canada license-exempt RSS standard(s). Operation is subject 
to the following two conditions: (1) this device may not cause 
interference, and (2) this device must accept any interference, 
including interference that may cause undesired operation of 
the device.

Par RSS-Gen, Section 8.4 cet appareil est conforme à la norme 
RSS Industrie Canada exempt de licence. Son fonctionnement 
est soumis aux deux conditions suivantes: (1) cet appareil 
ne doit pas provoquer d’interférences et (2) cet appareil doit 
accepter toute interférence, y compris les interférences pouvant 
causer un mauvais fonctionnement du dispositif.

Accessories

SE-ANT210

Whip/straight  

2.4 GHz antenna, 

IP65, connector 

mount.

SE-ANT250

Dome  

2.4 GHz antenna,  

IP67, panel mount,  

9.8ft/3m cable length.

C2-FILL

Snap-on CPU Option 
Slot cover for applications 
without an Option Slot 
module present.

C0-4TB

Replacement terminal 
block for the 24VDC 
power connection.  
Sold in packs of 2.

D0-MC-BAT

Replacement battery for 
CLICK PLUS CPU units.

Summary of Contents for CLICK PLUS C2-02CPU











Reviews: