background image

Chapter 1:  Getting Started

Page 1–5

S

tride

®

 MB Gateway User Manual

 – 

1st Edition Rev. E – August 2020

Hardware Reset Button

The Hardware Reset Button is a small 

recessed button located on the top of the 

device. Pressing the button will reset all 

settings to their default values.

DIP Switches

A 120Ω termination resistor for each serial 

port is enabled (ON) or disabled (OFF) by the 

corresponding DIP switch.

LEDs

The front panel provides status via the 

following LEDs:

PWR1 (Green)

LED ON indicates voltage is applied to 

Power 1 terminals.

PWR2 (Green)

LED ON indicates voltage is applied to 

Power 2 terminals.

RUN (Green)

Blinking Indicates the device is functioning 

normally. Steady on indicates power is on 

and device is booting up.

SPEED (RJ45 Yellow)

There is one yellow SPEED LED for each 

Ethernet port. LED ON indicates Ethernet 

speed is 100 Mbps. LED OFF indicates 

Ethernet speed is 10 Mbps. 

Link/Activity (RJ45 Green)

There is one green 

L

ink

/A

ctivity

 LED for each 

Ethernet port. The 

L

ink

/A

ctivity

 LED is ON 

when a valid link is established, and flashes 

to indicate that the gateway sees data traveling on the Ethernet network. If any network device 

is sending or receiving data, the 

L

ink

/A

ctivity

 LED will be flashing. During heavy communication 

loads, this indicator will be steady ON. If the LED is OFF, then a problem with the Ethernet 

connection has been detected.

T (Serial port Transmit, Green) 

The T or 

t

rAnsmit

 D

AtA

 LED flashes to indicate that the gateway is sending data through the serial 

port.

R (Serial port Receive, Green) 

The R or 

r

eceive

 D

AtA

 LED flashes to indicate that the gateway is receiving data through the serial 

port.

Chassis Ground

Power Connection

Dip Switches

Hardware Reset Button

Summary of Contents for STRIDE SGW-MB1511-T













Reviews: