background image

 

Owner Installation Instructions 

GDO-8 Shed Master® 

13

Setting Limits

5. Fixing of door curtain to drumwheel

The door curtain has to be secured to the drum wheel 
with suitable fasteners.  This prevents unauthorised 
access through the door by pushing the curtain up and 
off the drum.

1. With the door in the fully closed position, mark the 

curtain 

(Fig. 07)

 on both ends of the door.

2. Open door slightly to have access to the marked 

positions. Secure the curtain to drum wheel using 
self drilling screws (two on each end). The screws 
should be at least 90 degrees apart.

6. Setting Limits
6.1 Connect Power to the Powerhead

Plug the power cord into a mains point and switch power 
on. The red CLOSE LIMIT LED will be fl ashing.

6.2 Coding transmitter for setting limits

1. Press and hold the Door Code button 

(Fig. 09).

2. Press button 1 

(Fig. 11)

 on the transmitter for 

two seconds.

3. Release and pause for two seconds.
4. Press the same button transmitter again for 

two seconds.

5. Release the Door Code button.

NOTE: 

If PE Beams are to be used they must be 

installed before setting the travel limits.

WARNING: 

The safety obstruction detection 

system is inoperable while MINUS (-) and PLUS (+) 
drive buttons are being used and travel limits are 
not set.

IMPORTANT NOTE: 

The OPERATE button will 

not function until the open and close limits 
positions are set.

07

fi g

Drum wheel

90°

Summary of Contents for GDO-8 Shed Master





























Reviews: