background image

26

GDO-8V3 

Shed Master Instruction Manual

10. Customer Agreement & Warranty

PLEASE READ THIS AGREEMENT CAREFULLY TO ENSURE THAT YOU UNDERSTAND EACH PROVISION.  THIS AGREEMENT REQUIRES THE USE OF 

ARBITRATION ON AN INDIVIDUAL BASIS TO RESOLVE DISPUTES, RATHER THAN JURY TRIALS OR CLASS ACTIONS, AND ALSO LIMITS THE REMEDIES 

AVAILABLE TO YOU IN THE EVENT OF A DISPUTE.

This Agreement, the product manual, Limited Warranty terms below, terms and conditions, and terms of service for garage door opener products, features, and 

applications (“Products”) not otherwise described herein that are posted on applicable ATA  websites or devices, and any documents expressly referred to herein or 

therein, make up the complete agreement between you and ATA and supersede any and all prior agreements and understandings related to the subject matter of 

this Agreement.  

WARRANTY PERIOD

MOTOR & PARTS

5 years / 10,000 cycles

which ever occurs first

ACCESSORIES

(

e.g Safety Beams)

1 Year

CONSUMABLES 

(e.g Batteries in remote control 

transmitters and light bulbs and fuses)

Not covered

This Warranty is to be read in conjuction with the owner’s copy of the installation instruction 

manual.

LIMITED WARRANTY

1.  The product will operate properly providing you comply with the instructions 

concerning installation, operation, and maintenance and testing. Failure to 

act in accordance with those instructions may void all or part of this limited 

warranty.

2.  The warranty periods for different parts of this product are set out in the table 

above. If during the relevant warranty period, this product appears to contain 

a defect in a component  covered by this limited warranty, call your Retailer, 

who will advise you how to disassemble it and to send in a suitably secured 

packaging, pre-paid and insured, to a service center. Please include a brief 

description of the problem and a dated proof-of-purchase receipt. 

3.  If ATA confirms the product is defective and covered by this limited warranty, 

ATA will be repair or replace it (at ATA’s sole option) and return it to you, at no 

cost to you. Defective parts will be repaired or replaced with new or factory-

rebuilt parts at ATAs sole option. (You are responsible for any costs incurred in 

removing and/or reinstalling the product or any component).

4.  THIS WARRANTY EXCLUDES DAMAGE RESULTING FROM: 

(A) NORMAL WEAR AND TEAR;

(B) ACCIDENTAL DELIBERATE OR NEGLIGENT DAMAGE OR DAMAGE CAUSE 

BY INSECTS;

(C) BLOWN FUSES, ELECTRICAL SURGES, POWER SURGES OR POWER SPIKES;

(D) THEFT, FIRE, FLOOD, RAIN, WATER, LIGHTNING, STORMS OR ANY OTHER 

ACTS OF GOD;

(E) ANY INSTALLATION, CONFIGURATION OR USE OF THE PRODUCT 

CONTRARY TO THE INSTRUCTIONS SUPPLIED WITH THE PRODUCT;

(F) MAXIMUM CONTINUOUS OPERATING TIME EXCEEDING 1 MINUTE IN 10;

(G) THE OPERATING FORCE EXCEEDING 33LBS (150 NEWTON) WHEN MOVING 

THE DOOR MANUALLY TO THE OPEN OR CLOSED POSITION (THE DOOR 

THAT THE PRODUCT IS USED WITH SHOULD BE BALANCED IN SUCH A 

WAY THAT THE USER IS ABLE TO OPEN OR CLOSE THE DOOR MANUALLY 

USING A FORCE NOT GREATER THAN 150 NEWTON (33 LBS), OTHER THAN 

TO INITIALLY CAUSE THE DOOR TO START MOVING, WHICH MAY REQUIRE 

FORCE IN EXCESS OF THAT SPECIFIED IN THIS PARAGRAPH) ;

(H) DOOR SURFACE AREA AND/OR WEIGHT EXCEEDING 92FT2 AND 595LBS 

RESPECTIVELY;

(I)  THE DOOR USED WITH THE PRODUCT NOT BEING IN SAFE WORKING 

ORDER AND CONDITION;

(J) REPAIRS WHICH ARE NOT AUTHORIZED BY ATA;

(K) ANY UNAUTHORIZED MODIFICATION TO THE PRODUCT OR ACTS OR 

OMISSIONS OF ANY PERSON (INCLUDING SERVICE PROVIDERS APPROVED 

BY ATA) OTHER THAN ATA;

(L) FAULTY OR UNSUITABLE WIRING IN THE BUILDING IN WHICH THE 

PRODUCT IS INSTALLED;

(M) 

ANY COST OR EXPENSE RELATING TO THE RECALL OF THE 

PRODUCT;

(N) INSTALLATION OF A RESIDENTIAL GARAGE DOOR OPENER IN A 

COMMERCIAL OR INDUSTRIAL PREMISES OR IN A DWELLING OTHER 

THAN A SINGLE-FAMILY DWELLING;

(O) RADIO OR ELECTRICAL INTERFERENCE; OR LACK OF AVAILABILITY OR

(I)  DOOR SURFACE AREA AND/OR WEIGHT EXCEEDING 92FT2 AND 

595LBS RESPECTIVELY;

(II) THE DOOR USED WITH THE PRODUCT NOT BEING IN SAFE WORKING 

ORDER AND CONDITION

5.  This Warranty is not transferable.

6.  No additional warranty will apply for Products repaired during the relevant 

warranty period.

7.  For all Products repaired outside the warranty period charges may apply and 

a six (6) month warranty that the Product will be free of any defects in material 

and workmanship will apply from the date of return of the Product to you.

8.  Where the Product is sold by any person other than ATA, except for the 

warranty set out above, such person has no authority from ATA to give any 

warranty or guarantee on ATA’s behalf in addition to the warranty set out 

above.

9.  LIMITATION ON LIABILITY AND DAMAGES EXCLUSION - EXCEPT 

AS EXPRESSLY PROVIDED IN THIS LIMITED WARRANTY AND THE 
USER TERMS, ATA MAKES NO REPRESENTATIONS, GUARANTEES, 
CONDITIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED.   ANY 
OTHER STANDARDS OF PERFORMANCE, GUARANTEES, CONDITIONS 
AND WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED AND 
DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW.  THIS 
DISCLAIMER AND EXCLUSION SHALL APPLY EVEN IF THE EXPRESS 
LIMITED WARRANTY CONTAINED IN THE LIMITED WARRANTY AND 
USER TERMS FAILS OF ITS ESSENTIAL PURPOSE.

10. 

ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW 

SHALL BE LIMITED TO THE DURATION OF THE LIMITED WARRANTY 
ABOVE.  OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS 
PROVIDED UNDER SUCH EXPRESS LIMITED WARRANTY IS PROVIDED 
IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.  TO THE 
FULLEST EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW, 
ATA WILL IN NO EVENT BE LIABLE, WHETHER IN CONTRACT OR TORT 
OR ANY OTHER LEGAL THEORY, INCLUDING WITHOUT LIMITATION 
STRICT LIABILITY, GROSS NEGLIGENCE OR NEGLIGENCE, FOR ANY 
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR 
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL 
OR PUNITIVE DAMAGES OF ANY KIND REGARDLESS OF WHETHER ATA 
WAS ADVISED OR THE POSSIBILITIES OF SUCH DAMAGES.  ATA IS NOT 
LIABLE FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU 
FOR A THIRD PARTY.

TERMS RELATING TO THE USE AND LIMITATIONS OF SERVICE

1.  WHAT ARE THE LIMITATIONS ON SERVICE AND LIABILITY?

a.  Unless prohibited by law, the following limitations of liability apply. Service 

may be interrupted, delayed, or otherwise limited for a variety of reasons, 

including environmental conditions, unavailability of radio frequency 

channels, system capacity, priority access by National Security and Emergency 

Preparedness personnel in the event of a disaster or emergency, coordination 

with other systems, equipment modifications and repairs, and problems with 

the facilities of interconnecting carriers.

b.  Additional hardware, software, subscription, credit or debit card, Internet 

access from your compatible PC and/or special network connection may 

be required and you are solely responsible for arranging for or obtaining all 

such requirements. Some solutions may require third party products and/or 

services, which are subject to any applicable third party terms and conditions 

and may require separate purchase from and/or agreement with the third 

party provider.  ATA is not responsible for any consequential damages caused 

in any way by the preceding hardware, software or other items/requirements 

for which you are responsible.

c.  Not all Services are available for purchase or use in all sales channels, in all 

areas or with all devices. ATA is not responsible for loss or disclosure of any 

sensitive information you transmit. ATA is not responsible for nonproprietary 

services or their effects on devices.

Summary of Contents for DOMINATOR ShedMaster GDO-8V3





























Reviews: