Automatic Products SNACKSHOP LCM3 Series, Instruction Manual

Page: 14 / 81

components
10
components
Removing Delivery Bin.
a. Remove the screws from the left and right
bracket of the delivery bin.These screws fas-
ten into the lower door brace and remove the
screws and brackets at the top of the delivery
bin.
b. Grasp delivery bin on both sides, lift up and pull back.
Should bin be tight, rock it by lifting on one end, then the
other.
Replacing Delivery Bin.
a.Locate lip on front edge of delivery bin, over lower edge of
opening in door and behind trim. Press down along lip to
make sure it is fully engaged between door and trim.
b. Install the 4 screws and 2 brackets, to secure bin to door.
12. Replacing Vend Can Motors or Sold-Out Switch e s .
Before replacing a vend motor, the selection must first be
emptied of cans. When replacing any of the five motors on
the bottom, you must also remove all the cans from the
selection directly above it to remove the old motor.
a. Remove the cans using any of the following methods:set-
ting the machine to test vend, setting the vend price to 00,
or removing the link arm from the vend motor and ratch-
eting the cans out manually. Once the cans are removed
turn the main power switch off.
b. Remove the third shelf from the machine.
c. Remove the two middle screws on top of the cooler door
and lift the door off.
d. Remove the link arm (Page 45, /Item 15.) from the motor
assembly.
e. Remove the three screws holding the motor support plate
to the rack assembly and swing motor up and out to
remove.
f. Remove the wires from the common terminal on the cycle
microswitch and the small terminal on the motor.
g. To install motor, reverse above procedure.
13. Cooler Assembly. When placing a LCM4 machine at a
location, CAUTION should be taken to keep adequate
clearance in the rear and front bottom screens for proper
circulation.The front screen assembly should be removed
and cleaned regularly for proper operation of the refrigera-
tion system.
The cold control is located inside the cooler unit on the bot-
tom right corner (Page 41, Item 1) with the standard setting
set on #4.
14. Removal of Can Dispensing Unit.
a.Remove the third shelf from the machine.
b. Remove the middle two screws from the
top of the cooler door. (Page 35., Item 10.) Tilt the com-
plete door assembly down and lift up for removal.
c. Remove the two “L” brackets holding the cooler assem-
bly to the cabinet. (Page 39., Item 27.) Disconnect the
two plugs from the right-hand side of the cooler unit.
d. Pull the can unit out. (Because of the weight, it is rec-
ommended that two persons complete this task.)
e. Remove the four corner screws (not shown) on can unit
underside and one front center screw that attaches the
can unit with the refrigeration unit.
f. Lift can unit off for exposure to the refrigeration unit.
15. R e m oval of Gum and Mint Motor
and/or Ejectors.
Disconnect the two wires going to the motor
and remove the four screws holding it to the
shelf. The components attached to the front base can also
be replaced.These consist of the gum and mint shelf front
(Price tabs and selection), gum and mint shelf front base,
gum and mint display front stop (plastic) and the gum and
mint ejector.
16.
Chilled Air Machine.
When placing a chilled machine at a location CAUTION
should be taken to keep adequate clearance in the rear
and front bottom screen for proper circulation. The front
vent screen assembly should be removed and cleaned
p e riodically for proper operation of the refri g e ration
system.
17. Removal of Cooling Unit - LCM3 Only.
Replacing a cooling unit can be done by
r e m oving the two screws from the Air Duct
S u p p o rt Bra cke t . Then, lift the air duct up and
out of the cooling unit. R e m ove the two
s c r ews in the bottom of the cooling pan located to the ri g h t
and next to the bl owe r. R e m ove the two screw s. The cooling
unit can now be pulled straight out from the angle guides.
R everse the procedure to put the cooling unit back in the
m a c h i n e.
NOTE: The cold control setting (Page 47., Item 7.)
should be set on the #4 position.
N OT E : B e fore replacing the gum and mint motor,
it would be helpful to tap the motor first with the
s c r ew s . A s s e m ble the four components toge t h e r
and mount them to the motor making sure that
the head crank of the motor is inserted into the
e j e c t o r. Replace the four screws and test vend
that selection for proper operation.
IMPORTANT: Removal or damage of the screen can
cause air flow problems resulting in damage to the
refrigeration system.