Autoglide CASA-50P User Manual Download Page 3

INSTRUCTIONS CASA-50P 

 

Page 3

 

                                 SLIDING GATE OPENER 

 

 

Warnings

 

 

 

Please  read  this  instruction  manual  carefully  before  the  installation  of  gate-automated 
system.

 

 

This  manual  is  exclusively  for  qualified  installation  personnel. 

Autoglide

  is  not 

responsible  for  improper  installation  and  failure  to  comply  with  local  electrical  and 
building regulations.

 

   Keep  all  the  components  of  CASA-50P  system  and  this manual for further            
   consultation 

 

Be  aware  of  the  hazards  that  may  exist  in  the  procedures  of  installation 
and  operation  of  the  gate-automated  system.  Besides,  the  installation 
must  be  carried  out  in conformity with local standards and regulations                                                         

 

If the system is correctly installed and used following all the standards and 
regulations, it will ensure a high degree of safety

 

 

Make  sure  that  the  gates  works  properly  before  installing  the  gate-
automated  system  and  confirm  the  gates  are  appropriate  for  the 
application.

 

 

Do    not    let    children    operate    or    play    with    the gate-automated 
system.

 

 

Do not cross the path of the gate-automated system when operating.

 

 

Please  keep  all  the  control  devices  and  any  other  pulse  generator  away 
from  children  to  avoid  the  gate-automated  system  being  activated 
accidentally.

 

 

Do  not  make  any  modifications  to  any  components  except  that  it  is 
mentioned in this manual.

 

 

Do not try to manually open or close the gates before you release the gear 
motor.

 

 

If  there  is  a  failure  that  cannot  be  solved  and  is  not  mentioned  in  this 
manual, please contact qualified installation personnel.

 

 

Do  not  use  the  gate-automated  system  before  all  the  procedures  and 
instructions have been carried out and thoroughly read.

 

 

Test  the  gate-automated  system  weekly  and  have  qualified  installation 
personnel to check and maintain the system at least every 6-month.

 

 

Install  warning  signs  (if  necessary)  on  the both  sides  of  the  gate  to  warn 
the people in the area of potential hazards.                                                                                                        

 

Summary of Contents for CASA-50P
















Reviews: