AutoCrib RoboCrib 2000 E Operation Manual Download | Manualshive

Page: 53 / 53

background image

Care and Maintenance

53 |

P a g e

Care and Maintenance

Repairs

Disconnect defective equipment from power immediately
(unplug the equipment from the wall outlet). Any attempt by
untrained persons to perform repairs may result in
considerable hazards for the user.

Important Note: If the equipment is still under warranty,
contact AutoCrib Technical Support for repair/replacement
instructions.

If a cable or cable gland is damaged or defective, replace
the cable as a complete unit with all of its connectors.

Do not open the scale while it is carrying current. Allow
approximately 10 seconds to elapse after disconnecting the
equipment from power before opening the equipment
housing. Proper fitting of all surfaces is essential for the 1P
rating of the housing; for this reason the device must be
opened and closed by a certified technician.

Safety Inspection

Safe operation of the scale is no longer ensured when:

-

There is visible damage to the device or power
cord

-

The built-in power supply no longer functions
properly

-

The device has been stored for a relatively long
period under unfavorable conditions (e.g., extreme
moisture)

If there is any indication that safe operation of the scale is
no longer warranted:

-

Disconnect the equipment from power

-

Notify AutoCrib Technical Support

Cleaning

Disconnect the scale from power (unplug from the wall
outlet) and disconnect any data cables.

Make sure that no liquid penetrates the scale housing.

Do not use any aggressive cleaning agents (solvents or
similar agents).

Do not was down the equipment with water or dry it with
compressed air; this is not permitted.

>

Clean the scale using a piece of cloth, which has been

wet with a mild detergent (soap).

>

After cleaning, wipe down the display and control unit with

a soft, dry cloth.

Cleaning Stainless Steel Surfaces

Clean all stainless steel parts regularly. Use a damp cloth
or sponge to clean stainless steel parts on the scale. You
can use any household cleaning agent that is suitable for
use on stainless steel. Clean stainless steel surfaces by
wiping them down. Then rinse the equipment thoroughly,
making sure to remove all residues, and allow the
equipment to dry. If desired, you can apply oil to the
cleaned surfaces as additional protection. Solvents are
permitted only for cleaning stainless steel parts.

«
...
51
52
53

Summary of Contents for RoboCrib 2000 E






















































Reviews:

No comments

Related manuals for RoboCrib 2000 E

Brand: Necta Pages: 13

Brand: Fellowes Pages: 4

Brand: Singer Pages: 12

Brand: Karma Pages: 16

Brand: Uchida Yoko Pages: 25

Brand: Garudan Pages: 67

Brand: Janome Pages: 42

Brand: LAI Games Pages: 72

1888 Foot-Bar Set of attachments

Brand: Singer Pages: 20

HZL - 353Z Series

Brand: JUKI Pages: 35

Brand: LAUREL Pages: 2

Brand: Laurel Metal Products Incorporated Pages: 4

Brand: Brother Pages: 2

Brand: Brother Pages: 2

Brand: Brother Pages: 57

Brand: Brother Pages: 8

Brand: Brother Pages: 44

Brand: Brother Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands