background image

2

27

LIMITED WARRANTY

12 MONTHS FROM DATE OF PURCHASE-

CABLES 90 DAYS

The manufacturer warrants to the consumer that this product 

will be free from defects in material or workmanship for 

a period of twelve (12) months from the date of original 

purchase.  

Products that fail within this 12 month warranty period will 

be repaired or replaced at the manufacturer's option to the 

consumer, when determined by the manufacturer that the 

product failed due to defects in material or workmanship.  This 

warranty is limited to the repair or replacement of parts and 

the necessary labor by the manufacturer to effect the repair or 

replacement of the product.  In no event shall the manufacturer 

be responsible for special, incidental or consequential damages 

or costs incurred due to the failure of this product.  

Improper use, accident, water damage, abuse, unauthorized 

repairs or alterations voids this warranty.  The manufacturer 

disclaims any liability or consequential damages due to breach 

of any written or implied warranty on its test equipment.  

WARRANTY AND SERVICE INFORMATION

Warranty claims to the manufacturer's service department 

must be transportation prepaid and accompanied by a dated 

proof of purchase.  This warranty applies only to the original 

purchaser and is non-transferable. Freight damage incurred 

during return shipments is not covered under this warranty.  It 

is the responsibility of the shipper (the customer returning the 

Test Equipment) to package the tester properly to prevent any 

damage during return shipment.  Repair costs for such damages 

will be charged back to shipper (customer returning the Test 

Equipment).  Protect the product by shipping in original carton 

or add plenty of over-pack cushioning such as crumpled up 

newspaper.  

Summary of Contents for BVA-350





























Reviews: