Autel MaxiIM KM100 Manual Download

Page: 60 / 82

that the tool is connected to the MaxiVCI V200 and is ready
to perform vehicle diagnosis.

Tap the paired device again to disconnect it.

Tap the

Home

icon on the top-left to return to the MaxiIM Job

Menu.

NOTE

A MaxiVCI V200 can be paired to only one tool at a time, and once it is paired,
the device will not be discoverable to other devices.

10.3.2 Firmware Upgrade

Before upgrading the V200 firmware, ensure your Internet connection is
stable. The V200 supports both Bluetooth and USB communications.

Figure 10-3 Firmware Upgrade Screen

Upgrade via Bluetooth



To upgrade the MaxiVCI V200 firmware via Bluetooth

1. Connect the V200 to the vehicle or charge it with an adapter

before pairing it with the tool via Bluetooth.

2. On the MaxiIM Job Menu, tap

Settings

VCI Manager

, and

Summary of Contents for MaxiIM KM100



















































































Search results

Summary of Contents for MaxiIM KM100

Reviews:

Related manuals for MaxiIM KM100

Brands by name

Popular brands

Autel MaxiIM KM100, Manual

Search results

Summary of Contents for MaxiIM KM100

Reviews:

Related manuals for MaxiIM KM100

Brands by name

Popular brands