Austro Engine IAE50R-AA Manual Download Page 7

Page: 7 / 87

ENGINE MANUAL

IAE50R – AA

E1.01.05 – E

Issue date: 25.Jan.2018

Page: 0-4

Revision no: 9

19.2

GND Concept IAE50R

.................................................................................................................. 19-12

19.3

Sensors and actuators

................................................................................................................. 19-13

19.3.1

Air Temperature sensor

.......................................................................................................... 19-13

19.3.2

Rotor cooling air out temperature sensor

............................................................................ 19-14

19.3.3

Map Sensors

............................................................................................................................. 19-16

19.3.4

Speed Sensors

.......................................................................................................................... 19-17

19.3.5

Ignition Coils

............................................................................................................................. 19-18

19.3.5.1

H.T. Leads

........................................................................................................................................ 19-19

19.3.5.2

Spark plugs

...................................................................................................................................... 19-19

19.3.6

Injector

...................................................................................................................................... 19-20

19.3.7

Coolant Temperature Sensor for instruments

...................................................................... 19-21

19.4

Generator regulator and Generator wiring

............................................................................... 19-22

19.4.1

Mechanical installation of the Generator Regulator

............................................................ 19-22

19.4.2

Electrical installation of the Regulator

.................................................................................. 19-23

19.5

Starter

............................................................................................................................................ 19-24

19.5.1

Mechanical installation

............................................................................................................ 19-24

19.5.2

Electrical connection of starter

.............................................................................................. 19-24

19.6

Electronic Components Capability

.............................................................................................. 19-25

19.6.1

Electrical tests

........................................................................................................................... 19-25

19.6.2

Environmental tests

................................................................................................................. 19-26

19.6.3

Control System Reliability

....................................................................................................... 19-27

19.6.3.1

Control system reliability objective.

.............................................................................................. 19-27

19.6.3.2

Software Quality level

..................................................................................................................... 19-27

Summary of Contents for IAE50R-AA
























































































Search results

Summary of Contents for IAE50R-AA

Reviews:

Brands by name

Popular brands

Austro Engine IAE50R-AA, Manual

Search results

Summary of Contents for IAE50R-AA

Reviews:

Brands by name

Popular brands