manualshive.com logo in svg

Austro Engine IAE50R-AA, Manual

Share
Download
Austro Engine IAE50R-AA Manual Download Page 4

 

ENGINE MANUAL 

IAE50R – AA 

E1.01.05 – E 

 

 

Issue date: 25.Jan.2018 

Page: 0-1 

 

Revision no: 9

 

0

 

TABLE OF CONTENTS 

0

 

TABLE OF CONTENTS

 ..................................................................................................................... 0-1

 

1

 

INTRODUCTION

 .............................................................................................................................. 0-1

 

1.1

 

Record of Revisions

 .......................................................................................................................... 1-2

 

1.2

 

List of Revisions

 ................................................................................................................................ 1-3

 

1.3

 

List of Valid Pages

 ............................................................................................................................ 1-5

 

1.4

 

List of Incorporated Temporary Revisions

 .................................................................................... 1-7

 

2

 

GENERAL INFORMATION

 .............................................................................................................. 2-1

 

3

 

SAFETY INFORMATION

 ................................................................................................................. 3-1

 

3.1

 

Safety Symbols

 ................................................................................................................................. 3-1

 

3.2

 

Model Designation Breakdown

 ....................................................................................................... 3-2

 

3.3

 

Replacement parts

 ........................................................................................................................... 3-2

 

4

 

RESERVED

 ......................................................................................................................................... 4-1

 

5

 

GENERAL ENGINE DATA

 ................................................................................................................ 5-1

 

5.1

 

Description

 ........................................................................................................................................ 5-1

 

5.2

 

Technical data

 ................................................................................................................................... 5-1

 

5.2.1

 

Design Responsibility

 ................................................................................................................... 5-1

 

5.2.2

 

Certification

 ................................................................................................................................... 5-1

 

5.2.3

 

Engine Overall Dimensions

 ......................................................................................................... 5-2

 

5.2.4

 

Engine Particulars

 ........................................................................................................................ 5-3

 

5.2.5

 

Out – put Drive

............................................................................................................................. 5-3

 

5.2.6

 

Net Dry Weight

 ............................................................................................................................. 5-3

 

5.2.7

 

Cooling

 ........................................................................................................................................... 5-4

 

5.2.8

 

Fuel Specification

 ......................................................................................................................... 5-4

 

5.2.9

 

Fuel Consumption Curve

 ............................................................................................................. 5-4

 

5.2.10

 

Pressure to Fuel Injector

 ............................................................................................................ 5-5

 

5.2.11

 

Lubrication

 .................................................................................................................................... 5-5

 

5.2.12

 

Oil Specification

 ............................................................................................................................ 5-5

 

6

 

OPERATING DATA / LIMITATIONS

 ............................................................................................ 6-1

 

6.1

 

Maximum Take – off Rating

 ............................................................................................................ 6-1

 

6.2

 

Maximum Continuous Rating

 .......................................................................................................... 6-1

 

6.2.1

 

Power Curve

 ................................................................................................................................. 6-2

 

6.3

 

Operating Limitations

....................................................................................................................... 6-2

 

6.3.1

 

Engine RPM

 ................................................................................................................................... 6-2

 

6.3.2

 

Ambient Temperature Limits

 ...................................................................................................... 6-2

 

6.3.3

 

Liquid Coolant Temperature Limits

 ........................................................................................... 6-3

 

6.3.4

 

Rotor Cooling Air Outlet Temperature Limits

 ........................................................................... 6-3

 

6.3.5

 

Exhaust Gas Temperature (EGT)

 ............................................................................................... 6-3

 

6.3.6

 

Fuel Pressure

 ................................................................................................................................ 6-3

 

6.3.7

 

Altitude

 .......................................................................................................................................... 6-3

 

6.4

 

Manuals

 .............................................................................................................................................. 6-3

 

7

 

COMPONENTS

 .................................................................................................................................. 7-1

 

7.1

 

Description of Components

 ............................................................................................................. 7-2

 

7.1.1

 

Rear Assemblies

 ........................................................................................................................... 7-2

 

7.1.2

 

Front Assemblies

 .......................................................................................................................... 7-2

 

7.1.3

 

Centre and Rotating Assembly

 ................................................................................................... 7-2

 

7.1.4

 

Rotor Sealing

 ................................................................................................................................ 7-2

 

Summary of Contents for IAE50R-AA
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands