Aussie Bonza Deluxe Series Use Manual Download Page 4

1-(800)-251-7558

8 am - 6 pm E.S.T Mon. - Fri.

1-(423)-639-1171 (TELEPHONE)

1-(423)-639-2570 (FAX)

CONSUMER SERVICE DEPARTMENT

MECO CORPORATION

1500 INDUSTRIAL ROAD

GREENEVILLE, TN 37745 USA

www.meco.net

30. Use of this LP gas grill other than for the intended 

use,       or alteration of this LP gas grill in any way may not 

be       safe and will void any warranty.

31. Never attempt to repair the LP gas grill or cylinder 

      yourself.  Contact the manufacturer for 

information       regarding repairs to your grill. 

32. LP gas is not natural gas.  The conversion or 

attempted       use of natural gas in an LP unit or LP gas in a 

natural       gas unit is dangerous and will void your warranty.

33. 

WARNING!

  Do not wear loose clothing (for 

      example: hanging shirt tails, clothing with frills, 

etc.)       around an LP gas grill while in use or hot.  

34. Never use an LP cylinder if it shows signs of: 

dents,       gouges, bulges, fire damage, corrosion, leakage, 

      excessive rust or other forms of visual external 

damage;       it may be hazardous and should be checked by 

a  

     Liquefied Petroleum supplier.  Do not use an LP 

cylinder       with a damaged valve.

35. Even though your LP cylinder may appear to be 

empty,       gas may still be present and the cylinder should 

be       transported and stored accordingly.

36. Never store an LP gas cylinder indoors (empty or 

filled).        If storing the gas grill indoors, disconnect LP gas 

cylinder       and store it outdoors out of the reach of children. 

37. Never leave an LP cylinder inside a vehicle which 

may       become overheated by the sun.

38. Never lean your body over the LP gas grill when 

lighting       it or while it is in use or hot.

39. Do not attempt to disconnect, move or alter any gas

      fittings while your LP gas grill is in operation.

40. Your LP gas grill should be cleaned on a regular 

basis.       Refer to Care and Maintenance section in this 

manual.

41. This LP gas grill is not designed to be used with 

more        than 50% of the cooking area as a solid plate 

(griddle).         Full coverage of plates will cause excessive 

heat and        could damage the grill.

42. Never douse the grill with water when its surfaces 

are        hot because it may cause grease to splatter or 

the        porcelain cooking grids and hood to break. Use bak-

ing soda to control a grease fire.

43. When not in use, the LP cylinder valve must be 

       turned to “Off” position.

44. Empty charcoal and wood chunk ashes after each use.        

 

 

 

 

 

 

 

 

45. Set up grill in an open area away from buildings, dry        

leaves, or brush. Be sure to avoid high traffic areas and 

always barbecue in a well-ventilated area. Be aware of wind 

blown sparks.   

 

 

 

 

 

 

 

 

 

 

 

   46. Never 

use lighter fluids. Never use gasoline, kerosene, alcohol, or 

other volatile fluids as a starter. They can explode. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

47. Once 

the charcoal briquettes are lit, do not touch to see if they are 

hot. 

 

 

 

 

 

 

 

 

 

 

 

 

 

  48. Allow 

coals to burn out completely and let the ashes cool        for 

48 hours before disposing of them. 

 

 

 

 

 

 

 

 

 

 

49. 

Dispose of cold ashes by wrapping them in heavy-duty alu-

minum foil and putting them in a non-combustible container. 

Be sure there are no other combustible materials in or near 

the container.   

 

 

 

 

 

 

 

 

 

 

 

50. If you 

must dispose of the ashes in less time than it takes for them 

to completely cool, remove the ashes from the grill keeping 

them in heavy duty foil and soak them completely with water 
before disposing in a non-       combustible container.

   

4

   MECO CORPORATION STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE INADVERTENTLY 

   OMITTED ANY PARTS NEEDED FOR ASSEMBLY, OR YOU NEED TROUBLESHOOTING INFORMATION, PLEASE CONTACT 

   US USING OUR TOLL FREE NUMBER.  THANK YOU FOR PURCHASING A MECO CORPORATION PRODUCT.

— NOTICE —

The purpose of these safeguards is to set forth general safety practices and precautions for the opera-

tion and maintenance of gas/charcoal grills. These tips are not intended to be an exhaustive treatment 

of the subject, and should not be interpreted as precluding other procedures which would enhance safe 

grill operations.

Summary of Contents for Bonza Deluxe Series




































Reviews: