manualshive.com logo in svg

Aussie Bonza Deluxe Series, Use Manual

Share
Download
Aussie Bonza Deluxe Series Use Manual Download Page 18

STEP 9-INSTALL BOTTOM BODY PANEL/GREASE TRAY- (ALL MODELS)

•In upright position and 

drain  hole  toward the rear, 

slide  Bottom Body  Panel 

into guides  (See Arrows) at 

 bottom of Grill  Body. Insert 

two #8 x  1/2”  screws 

through the holes in 

 guides and Bottom Body 

Panel; then  tighten. Slide 

Foil  Pan and Grease  Tray 

all the  way into Bottom 

Body  Panel  Brackets.

#8 X 1/2”   

SCREW 

(2pcs)

BOTTOM BODY PANEL

FOIL PAN

GREASE TRAY

UPPER SHOULDER

GRIDS

The foil pan is a complimentary item and can be purchased at your local grocery.

STEP 9-INSTALL BOTTOM BODY PANEL/GREASE TRAY- (ALL MODELS)

•In upright position and 

drain  hole  toward the rear, 

slide  Bottom Body  Panel 

into guides  (See Arrows) at 

 bottom of Grill  Body. Insert 

two #8 x  1/2”  screws 

through the holes in 

 guides and Bottom Body 

Panel; then  tighten. Slide 

Foil  Pan and Grease  Tray 

all the  way into Bottom 

Body  Panel  Brackets.

#8 X 1/2”   

SCREW 

(2pcs)

BOTTOM BODY PANEL

FOIL PAN

GREASE TRAY

UPPER SHOULDER

GRIDS

18

The foil pan is a complimentary item and can be purchased at your local grocery.

Summary of Contents for Bonza Deluxe Series




































Reviews:

No comments

Brands by name

Popular brands

Load more brands