AUMA ACV 01.2 Manual Download

Page: 85 / 168

For the setting

Immediately active

Risk of immediate actuator operation when switching on!

Risk of personal injuries or damage to the valve.

→

Ensure that the signal set under parameter

Source M0385

is present when

switching on.

→

If the actuator starts unexpectedly: Immediately turn selector switch to position
Local operation (LOCAL) or 0 (OFF).

9.2.2.

Failure source (failure reason) for a failure operation: set

Customer settings M0041

Failure behaviour M0378

Source M0385

Default value:

Active interface

Setting values:

Fieldbus interface

Failure behaviour is initiated in case of fieldbus communication loss.

I/O interface

The failure behaviour is initiated in case of setpoint loss (setpoint position, process
setpoint, actual process value).

The monitoring depends on the preset setpoint range, e.g.:

●

Setpoint = 4 – 20 mA, E1 lower than 3.7 mA = loss of signal

●

Setpoint = 10 – 20 mA, E1 lower than 9.7 mA = loss of signal

Information

●

For a setpoint range of 0 – 20 mA , monitoring is not possible.

●

Actuator controls will only respond to a setpoint signal loss, if a signal is present
at the

MODE

input, i.e. actuator controls are in operation mode Remote SET-

POINT (setpoint control).

Active interface

In case of fieldbus communication loss (if the fieldbus interface is active) or loss of
setpoints (if the I/O interface is active), the failure behaviour is initiated.

Possible failure reasons in case of fieldbus communication loss:

●

The connection to the master is interrupted.

●

The master goes into Clear state and sends:
-

either global control telegrams with the content Clear

or data telegrams of the length 0 (FailSafe mode).

9.2.3.

Failure operation (reaction of the actuator) on loss of signal

The failure operation defines which action is executed by the actuator once the failure
behaviour is initiated.

Customer settings M0041

Failure behaviour M0378

Failure operation M0384

Default value:

STOP

Setting values:

STOP

The actuator stops in the current position.

The actuator runs to end position CLOSED.

OPEN

The actuator runs to end position OPEN.

Approach position

The actuator runs to the specified position. Conditions:

●

The function <Positioner> is activated.

●

Parameter

Source M0385

is set to

I/O interface

(for fieldbus control:

Active interface

)

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Failure functions

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands