background image

E

5 BEEPS

HORN SOUNDS

E

VALET SWITCH ON THEN OFF

CHANNEL 5

" DEDICATED PANIC "

MEMORY

POSITION

# 1

MEMORY

POSITION

# 2

MEMORY

POSITION

# 3

MEMORY

POSITION

# 4

Do not program transmitter buttons to this channel. On the SE, the panic feature activates
from the Lock button. Continue on to the next step.

STEP 7

E

6 BEEPS

HORN SOUNDS

E

VALET SWITCH ON THEN OFF

CHANNEL 6

" REMOTE START "

MEMORY

POSITION

# 1

MEMORY

POSITION

# 2

MEMORY

POSITION

# 3

MEMORY

POSITION

# 4

If the Remote Start Upgrade Kit is installed into the vehicle, press the Green button ( hold the button
for 3 seconds until the horn sounds ) on all transmitters that you want to program ( up to 4 ), or
continue on to the next step.

STEP 8

STEP 9

TURN IGNITION KEY TO OFF

SOFT &

LOUD BEEP

HORN SOUNDS

PROGRAMMING

MODE TERMINATED

E

4 BEEPS

HORN SOUNDS

E

VALET SWITCH ON THEN OFF

CHANNEL 4

" HEADLIGHT "

MEMORY

POSITION

# 1

MEMORY

POSITION

# 2

MEMORY

POSITION

# 3

MEMORY

POSITION

# 4

If there are no SE upgrade kits ( IE: Trunk Release or Remote Starter ) installed into the
vehicle, press the Green button ( hold the button for 3 seconds until the horn sounds ) on all transmitters
that you want to program ( up to 4 ), or continue on to the next step.

STEP 6

E

3 BEEPS

HORN SOUNDS

E

VALET SWITCH ON THEN OFF

CHANNEL 3

" TRUNK RELEASE "

MEMORY

POSITION

# 1

MEMORY

POSITION

# 2

MEMORY

POSITION

# 3

MEMORY

POSITION

# 4

If the vehicle does not have the Trunk Release Upgrade Kit installed, proceed to step 6.

If the Trunk Release Upgrade Kit is installed into the vehicle, press the Green button ( hold the button
for 3 seconds until the horn sounds ) on all transmitters that you want to program ( up to 4 ), or
continue on to the next step.

STEP 5

E

2 BEEPS

HORN SOUNDS

E

VALET SWITCH ON THEN OFF

CHANNEL 2

" UNLOCK "

MEMORY

POSITION

# 1

MEMORY

POSITION

# 2

MEMORY

POSITION

# 3

MEMORY

POSITION

# 4

Now press the UNLOCK button ( hold the button for 3 seconds until the horn sounds ) on all transmitters
that you want to program ( up to 4 ), or continue on to the next step.

STEP 4

Page 3

Summary of Contents for SECURIKEY+













Reviews: