background image

128-8782b

9 of 12

Page 9

 128-8782b

OPERATING ON AUTOMATIC START UP TIMER MODE

The system has the ability to automatically start the vehicle every 2 or 4
hours over a 48 hour period. This feature is especially useful in cold
climates where the only means to keep the engine and engine fluids warm
is to periodically start the engine.

WARNING!

   Be certain that the vehicle is outdoors before using this

        or any remote vehicle starting device. A running engine
       produces dangerous carbon monoxide gases which can be

harmful or fatal if prolonged exposure occurs.

        DO NOT remote start the vehicle if the car is garaged.

TO BEGIN THE AUTOMATIC START UP TIMER

1. Turn the ignition key on then off.

2.  Within 10 seconds, activate the RF start command two times.
(Push the second channel button of your keychain transmitter 4 times).

The parking lights will flash 4 times indicating the timed start mode is
activated.

The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for
the pre-programmed run time, then shut off.

This will continue for 48 hours.

NOTE:

   The automatic start up timer can also be initiated from the keychain

transmitter.

To do this:

1.  Start the vehicle using the keychain transmitter by pressing and
     releasing the trunk/key button transmitter button 2 times.

2.  Shut off the vehicle using the keychain transmitter by pressing and

releasing the trunk/key transmitter button 2 times.

3.  Within 10 seconds of step 2, activate the RF start command two

  times.

     (Push the trunk/key button of your keychain transmitter 4 times).

Summary of Contents for Platinum+ APS 687C













Reviews: