There are several varied modes can be adjusted for Jog Wheel light ring.
1. To select light ring you desired; press PRESET button to enter internal menu, and turn FOLDER knob to
search “JOG MODE” menu.
2. Turn the TRACK knob to select the MODEs you want to adjust.
3. Press SHIFT button and turn TRACK knob to adjust the setting value.
(1). MODE 1 - It will show the playing point indicator around the ring. You can adjust the setting value range 1
of smallest indicator to 23 of full circle indicator.
(2). MODE 2 - It will indicate the playing point opposite (on->off / off
Æ
on) when the Jog Wheel is touched. You
can adjust the setting value range 1 of smallest indicator off to 23 of full circle off.
(3). MODE 3 - It will show the playing point indicator around the ring and flash to the playing level in both sides.
You can adjust the setting value range 1 of smallest playing point indicator to 23 of full circle indicator.
(4). MODE 4 - It will flash to the playing level around the ring.
(5). MODE 5 - It will always on. You can adjust the setting brightness range 1 to 100.
(6). MODE 6 - It will flash related to the setting speed. You can adjust the setting speed range 1 of fast flash to
100 of slow flash.
(7). MODE 7 - It will show the playing point similar to trail effect.
(8). MODE 8 - It will light when the Jog Wheel is touched.
9.
TAP BUTTON
- This button is used for manual BPM. When in manual BPM mode, tap this button to the beat of
the current track. Hold the TAP button for 1 sec. to activate Auto BPM.
10. PITCH BEND BUTTONS -
The desired pitch of CD decrease or increase when button is pressing and returns to
the original pitch when the button is released.
11. SAMPLE BUTTON -
a. Press this button, then press the desired BANK button to set the sample loop mode (LED is on).
b. When sample mode is set, then sampler will mix the music together.
c. And press the SAMPLE button again to set the sample single mode (LED is flash).
d. Press the SAMPLE button again to cancel sample function.
12. BANK BUTTONS 1~4 -
These buttons are used to store either four cue points or four samples. Each Bank
Button can store either a sample or a cue point. To play your programmed samples, press the Sample button and
then press the Bank Program button.
The stored Cue point will become sample when you change another CD or USB device or FOLDER to play.
13. SAVE BUTTON -
This button can be used in couple of ways:
a. Press this button to activate the memory mode, the save button LED will glow when active. After the memory
mode is activated, press your desired bank button to store your CUE point or playing loop.
b. To store your loops and cue points that are saved in the BANKS to the system memory for next time, press the
MEMORY button for 1 second.
NOTE:
RECALL MEMORY:
The device can store 2000 programmed cue points in 500 tracks for CD and 4
programmed cue points per track in the USB device. These setting may be recalled at any time, even
when an audio source has been removed and loaded at a later time.
To recall the bank memory with CD/USB device:
Turn the TRACK knob to select the track which with the BANKS and “Load Cues?” will be indicated on
the VFD, press MIDI PLAYER A (Y) to load or press MIDI PLAYER B (N) not to load. Or
press the SAVE button, LED on, and turn the TRACK knob to select the TRACK with BANKS that you
would like to recall.
14. CLEAR BUTTON
-
Press CLEAR button, LED on, or hold the CLEAR button to select the BANK buttons you
would like to clear.
15. PLAY/PAUSE BUTTON -
Each press of the button to change from play to pause or from pause to play.
16. CUE BUTTON -
Pressing the cue button during playback immediately pause playback and returns the tracks to
the last set cue point. In pause mode and the music is at the cue point, press the cue button to provide cue
monitor. The red cue led will lit when the music is at the cue point.
17. CUE PLAY BUTTON -
Press the button to return point and playing immediately. You can also tap the button to
create a BOP effect.
GENERAL FUNCTIONS AND CONTROLS
Top Panel
Page 32
