background image

2

ACX-600.1

Quick Start Guide

1. 

Read these instructions.  

2. 

Keep these instructions.

3. 

Heed all warnings.

4. 

Follow all instructions.

5. 

Do not use this apparatus near water.

6. 

Clean only with a dry cloth.

7. 

Do not block any ventilation openings. Install in accordance with the 
manufacturer’s instructions.

8. 

Do not install near any heat sources such as mufflers, silencers, exhaust 
pipes, or other apparatus (including amplifiers) that produce heat.

9. 

WARNING: Improper installation may lead to permanent injury or death. 
Installation of the apparatus must be done with great care by qualified 
personnel, to prevent damage to fuel lines, power and other electrical 
wiring, hydraulic brake lines, and other systems, that might compromise 
vehicle safety.

10.  P12V and Ground wiring of sufficient size to ensure adequate 

current to the amplifier. For the 

ACX-600.1

 this means 8 gauge wire or 

thicker.

11.   Use rubber grommets to protect wiring whenever passing wires through 

metal openings or bulkheads.

12.  Only use attachments/accessories specified by the manufacturer.
13.  Refer all servicing to qualified service personnel. Servicing is required 

when the apparatus has been damaged in any way, such as the power 
input terminals are damaged or objects have fallen into the apparatus, 
does not operate normally, or has been dropped.

14.  Fuses shall be replaced only with the correct type and fuse value, and 

only when the apparatus is powered off.

15.  Exposure to high sound pressure levels may lead to permanent hearing 

loss. Take every precaution to protect your hearing.

The lightning flash with arrowhead symbol within an equilateral 
triangle is intended to alert the user to the presence of uninsulated 
“dangerous voltage” within the product’s enclosure, that may be of 
sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to 
alert the user of the presence of important operating and mainte-
nance (servicing) instructions in the literature accompanying the 
appliance.

Caution: to reduce the risk of electric shock, do 
not disassemble the apparatus, other than to 
remove the top panel to access the controls. 
There are no user-serviceable parts inside. 
Refer servicing to qualified personnel.

Recycling notice: If the time comes and this apparatus has fulfilled 
its destiny, do not throw it out into the trash. It has to be carefully 
recycled for the good of mankind, by a facility specially equipped 
for the safe recycling of electronic apparatii. Please contact your 
local or state recycling leaders for assistance in locating a suitable 
nearby recycling facility. Or, contact us and we might be able to 
repair it for you.

Important Safety Instructions

Summary of Contents for ACX-600.1













Reviews: