AudioCodes Mediant 800Ci uCPE Quick Setup Manual Download Page 3

 

|

 

P a g e

 

 

 

Physical Description of Front Panel 

 

 

 

PWR 

LED indicating power status: 

 Green On

 

Power received by device. 

 Off 

No power. 
 

SYS 

LED indicating operating status: 

 Green On 

Device is operational.

 

 Green Flashing 

Initial rebooting stage or software upgrade in process.

 

 Red On 

Boot failure.

 

 Off 

Advanced rebooting stage. 

 

4G 

LED indicating 4G LTE cellular modem status: 

 Green On 

SIM card installed and an LTE cellular connection has 
been established. 

 Green Flashing 

In the process of connecting to the cellular network. 

 Red On 

 

No SIM card installed. 

 

SIM card is installed, but cannot connect to the 
cellular network (e.g., SIM failure). 

 Off 

 

Cellular interface has been configured but has been 
shut down (regardless of whether a SIM card is 
installed or not). 

 

Cellular interface is not configured or not licensed 
based on device's License Key (regardless of whether 
a SIM card is installed or not).  

 

 

 

SIM card slot for inserting a SIM card (mini-SIM card size) provided by your service for 
4G Long-Term Evolution (LTE) cellular modem (cellular WAN). 
 

CONSOLE 

RJ-45 port for RS-232 serial communication with the device. 
 

 

USB 3.0 port which can be used for storage on external USB flash disk. 

1  3  4  5 

Summary of Contents for Mediant 800Ci uCPE













Reviews: