AudioCodes IPmedia 3000 Installation Manual Download Page 55 | Manualshive

Page: 55 / 90

background image

Version 5.8

55

July 2009

Installation Manual

3. Installation

Figure

3-8: Patch Cable for 42 Spans

¾

To connect the E1/T1 trunk interfaces:

1.

Prepare a SCSI cable of suitable length to connect between RTM-8410 housed in Slot
1 and the PBX/PSTN switch. The connector at the RTM-8410 end of the cable should
be wired as shown in the tables below (one cable for the 100-pin connector and a
second cable for the 68-pin connector).

2.

For 42 and 84 spans configuration:

a.

Attach the Trunk cable with a 100-pin male SCSI connector to the 100-pin female
SCSI connector labeled

T1/E1 Trunks 1 to 25

.

b.

Attach the Trunk cable with a 68-pin male SCSI connector to the 68-pin female
SCSI connector labeled

T1/E1 Trunks 26 to 42

.

c.

For trunks 43 to 84, repeat steps a and b, but for the RTM-8410 housed in Slot 4.

3.

For 16-spans configuration:

attach the Trunk cable with a 100-pin male SCSI

connector to the 100-pin female SCSI connector labeled

T1/E1 Trunks 1 to 16

.

4.

Connect the other end of the Trunk cables to the PBX/PSTN switch.

Note:

For RTM-8410 in Slot 4, ignore the trunk numbers printed on the two SCSI
connectors.

«
...
53
54
55
56
57
...
»

Summary of Contents for IPmedia 3000



























































































Reviews:

No comments

Related manuals for IPmedia 3000

Brand: ICP DAS USA Pages: 8

Brand: RTA Pages: 93

TTN Gateway v1 - EU

Brand: The Things Network Pages: 20

Brand: PEHA Pages: 4

Brand: DAUDIN Pages: 24

Touchstone TG862G

Brand: Arris Pages: 48

Brand: EAE Pages: 22

Brand: Fastus Pages: 2

Brand: Aruba Pages: 20

Brand: Pahlen Pages: 19

Brand: VOPtel Pages: 38

Brand: Vbox Communications Pages: 88

Brand: ZyXEL Communications Pages: 2

Brand: Technicolor Pages: 114

Brand: Bang & Olufsen Pages: 58

Brand: SAGEMCOM Pages: 29

Brand: B+B SmartWorx Pages: 2

Brand: TECOM Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands