background image

One-Year Limited Warranty

Audio -Technica brand products purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc.
(A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at
our option, replaced with a new product of equal or superior value if delivered to A.T.U.S. or an authorized service center prepaid, together
with the sales slip or other proof of purchase date. 

Prior approval from A.T.U.S. is required for return.

This warranty excludes defects due

to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of
unauthorized repair or modification.

For return approval and shipping information,

contact the Service Department, Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow,

Ohio 44224.

Except to the extent precluded by applicable state law, 

A.T.U.S. will have no liability for any consequential, incidental, or special 

damages; any warranty of merchantability or fitness for particular purpose expires when this warranty expires.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Outside the U.S.A., please contact your local dealer for warranty details.

Audio-Technica U.S., Inc.,

1221 Commerce Drive, Stow, Ohio 44224  330/686-2600

P50791- B/ W   ©1995  Audio -Technica U.S., Inc.   Printed In U.S.A.

Summary of Contents for SmartMixer AT-MX341a













Reviews: