ES935ML6 SPECIFICATIONS
†
ELEMENT
Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN
MicroLine
®
FREQUENCY RESPONSE
30-20,000 Hz
LOW-FREQUENCY ROLL-OFF
80 Hz, 18 dB/octave
OPEN CIRCUIT SENSITIVITY
–35 dB (17.7 mV) re 1V at 1 Pa*
IMPEDANCE
250 ohms
MAXIMUM INPUT SOUND LEVEL
133 dB SPL, 1 kHz at 1% T.H.D.
DYNAMIC RANGE
(typical)
109 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO
1
70 dB, 1 kHz at 1 Pa*
SWITCH
Flat, roll-off
PHANTOM POWER
11-52V DC, 4 mA typical
REQUIREMENTS
WEIGHT
108 g (3.8 oz)
DIMENSIONS
316.3 mm (12.45") long,
8.0 mm (0.31") head diameter,
18.9 mm (0.74") base diameter
OUTPUT CONNECTOR
Integral 3-pin XLRM-type
OPTIONAL INTERCHANGEABLE
ESE-O omnidirectional (360°);
ELEMENTS
ESE-C cardioid (120°);
ESE-H hypercardioid (100°)
ACCESSORIES FURNISHED
AT8138 MicroLine foam
windscreen; AT8474 universal
isolation mount; AT8473 quick-
mount stand adapter;
5
/
8
"-27 to
3
/
8
"-16 threaded adapter
†In the interest of standards development, A.T.U.S. offers full details on its test
methods to other industry professionals on request.
*1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
8 kHz
Polar Pattern
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
200 Hz
1 kHz
5 kHz
Frequency in Hertz
LEGEND
12" or more on axis
Frequency Response
Response in dB
Roll-off
Audio-Technica U.S., Inc.,
1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited,
Old Lane, Leeds LS11 8AG England
www.audio-technica.com
P51933 ©2007 Audio-Technica U.S., Inc. Printed in U.S.A.
4. Using a 1" hole saw, drill the through-hole for the microphone
body. (Note: although a 1" drill bit will work, a hole saw provides
for a cleaner hole and is less likely to damage the table surface.)
5. Using a
1
/
16
" (1.5 mm) drill bit, drill three pilot holes for the
mounting screws. (If mounting below the table surface, be
certain
NOT
to drill pilot holes through the table.)
6. Place the AT8474 mount over the hole and partially tighten the
three screws. Then place the microphone in the AT8474 so that
the microphone's power module (base) extends through the
AT8474 mount into the hole. Tighten all three screws evenly.
For maximum security, the screws should be tight enough to
ensure that the microphone is held securely in place and can
not be removed without loosening the screws.
7. If mounting the AT8474 mount below the surface of the table,
slide the rubber trim ring over the microphone (above the table
surface) and seat it between the microphone and the sides of
the hole for a finished appearance. (If mounting the AT8474
above the surface of the table, you may also choose to use the
trim ring beneath the surface of the table, for added attenuation
of noise, shock and vibration.)
8. After installing the microphone, assure maximum shock mount
effectiveness by providing some slack in the connecting cable.
The cable can be secured to the table with a standard wire clip
or cable tie (not included).
0.31"
8.0 mm
5.17"
131.3 mm
12.45"
316.3 mm
7.28"
185.0 mm
0.74"
18.9 mm
