manualshive.com logo in svg

Audio Technica ATW-R5220, User Manual

Share
Download
Audio Technica ATW-R5220 User Manual Download Page 6

5

Part names and functions

ATW-R5220/ATW-R5220DAN

Front panel

❶ 

Power button ( 

 ) 

Use to turn the receiver on or standby.
(

: Symbol indicates standby.)

❷ 

IR sync window

Use to IR SYNC with the transmitter (ATW-T5201, ATW-T5202).

❸ 

Function button 1

Press to switch the main display and the level meter display.

❹ 

Function button 2

Press to switch the main display..

❺ 

Display

Displays the receiver state and setting menus.

❻ 

BACK button

Press to take the display back one screen.
Returns to the Main screen when pressed and held.

❼ 

Control dial

Displays the setting menu when you press the dial. Turn the dial to select a setting and press to confirm.
When you press and hold the dial, “TX SYNC” setting screen is displayed.

❽

  Headphone monitor

（

6.3 mm

）

output jack

This is the headphone output jack used for monitoring. It allows you to monitor receivers 1 and 2.

❾

  Headphone channel indicator

Displays which receiver is being monitored, receiver 1 or 2.

❿

  Headphone volume/Channel switch

Use when adjusting the volume of the headphones for monitoring.
Press and release the dial to switch between receivers 1 and 2.

•  Does not affect receiver audio output level.

❷

❶

❻

❼

❸ ❹

❺

❸ ❹

❽ ❾

❿

❺

❻ ❼

Summary of Contents for ATW-R5220




































Reviews:

No comments

Brands by name

Popular brands

Load more brands