Audio Technica ATW-R3210 User Manual Download | Manualshive

Page: 9 / 32

background image

8

How to insert batteries

ATW-T3201

1. Slide the battery cover latches down.

2. Open the battery cover while the latches are slid.

3. Insert the batteries according to the plus (+) and minus (-) marks

found inside the battery compartment.

ATW-T3202

1. Rotate the grip case of the battery compartment.

2. Open the battery cover.

• Put your finger on the hook of the battery cover and pull it to open the

battery cover.

3. Insert the batteries according to the plus (+) and minus (-) marks

found inside the battery compartment.

«
...
7
8
9
10
11
...
»

Summary of Contents for ATW-R3210

































Reviews:

No comments

Related manuals for ATW-R3210

Brand: NEC Pages: 10

GPSMAP 378 - Marine GPS Receiver

Brand: Garmin Pages: 2

Brand: Garmin Pages: 4

Echomap Plus 40 series

Brand: Garmin Pages: 6

Brand: Unifone Pages: 96

the t.bone IEM-75

Brand: thomann Pages: 40

Brand: AKG Pages: 28

Brand: Takstar Pages: 2

Brand: Bogen Pages: 8

Brand: RODE Microphones Pages: 8

Brand: Octet Matrix Audio Pages: 14

Brand: Insignia Pages: 2

Brand: Daewoo Pages: 27

Brand: FITNESS AUDIO Pages: 12

Brand: Uniden Pages: 1

Brand: Apex Digital Pages: 2

Brand: Blue Microphones Pages: 14

Brand: Boss Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands