Audio Technica ATW-R3210 User Manual Download

Page: 31 / 32

Specifications

ATW-T3202

RF output power

High: 30 mW, Low: 10 mW (switchable), at 50 ohms

Spurious emissions

Following federal and national regulations

Microphone capsule

Interchangable industry standard thread

High-pass (low-freq. roll-off)

150 Hz, 6dB/octave

Batteries

Two 1.5V AA, not included

Battery life*

High: 8.0 hours (alkaline)
High: 9.0 hours (Ni-MH)

Low: 9.0 hours (alkaline)
Low: 9.5 hours (Ni-MH)

Dimensions

ATW-T3202 (without capsule): 193 mm (7.60") long, 37 mm (1.46") maximum diameter
ATW-T3202/C510: 265 mm (10.43") long, 54 mm (2.13") maximum diameter
ATW-T3202/C710: 271 mm (10.67") long, 50 mm (1.97") maximum diameter

Weight (without batteries)

ATW-T3202 (without capsule): 200 g (7.1 oz)
ATW-T3202/C510: 330 g (11.6 oz)
ATW-T3202/C710: 314 g (11.1 oz)

Operating temperature range

-5 ºC to +45 ºC (23 º F to 113 ºF)

Included accessories

AT8456a Quiet-Flex™ stand clamp (5/8"-27 male to 3/8"-16 female threaded screw adapter)

* Depending on battery type, usage and environmental conditions.

For product improvement, the product is subject to modification without notice.

Summary of Contents for ATW-R3210

































Search results

Summary of Contents for ATW-R3210

Reviews:

Related manuals for ATW-R3210

Brands by name

Popular brands

Audio Technica ATW-R3210, User Manual

Search results

Summary of Contents for ATW-R3210

Reviews:

Related manuals for ATW-R3210

Brands by name

Popular brands