background image

2

Parts overview

The sound exhaust system can be retrofitted on both left
and right-hand drive vehicles.

Parts required:

Assembly set 8T0.071.901

Comprising:

Units

Part number

Description

1

8T0.071.905

Actuator, left

1

8T0.071.905.A

Actuator, right

2

8T0.071.910

Adjustable trim panel, chrome black

6

 

Stainless steel pop rivet, 4 x 9.5 mm (V2A)

2

1K0.253.141.M

Clamping sleeve

1

8T0.071.954

Wiring harness

1

8T0.071.953*

Control unit

1

8T0.071.952

Control unit holder

1

8T0.071.956

Sound exhaust system dual nozzle

1

 

Installation instructions

– Check the parts to ensure they can be installed in the re-

spective vehicle!

You will also need the following for vehicles with 4-cylinder
TDI engines:

Assembly set 8T0.071.901.A

Comprising:

Units

Part number

Description

1

8K0.253.409.E

Middle silencer, complete

1

8K0.253.144.F

Mounting for middle silencer

2

N.903.484.11

Hexagon nut with washer

1

8K0.253.144.M

Mounting for end silencer, right

1

1K0.253.141.M

Clamping sleeve

1

N.903.484.11

Securing nut for end silencer, right

1

8F0.804.172

Heat shielding plate for Cabrio and Sportback

1

8K0 804 172

Heat shielding plate for other vehicles

4

N.907.965.02

Securing nuts for heat shielding plate

4-cylinder TDI engines require the diffuser for the dual ex-
haust system 

⇒ 

 Electronic parts catalogue.

Installation instructions - Audi A4/A5 (B8 series) 2008 

Edition 11/2012

2

2  Parts overview

Summary of Contents for 2008 A5





















Reviews: