Auctus CONVERGENCE User Manual Download Page 11

Page: 11 / 19

Normally on

Slow flickering

Quick flickering

Status Indicator

Power indicator

Host Status

Power Indicator Status

Flicker Period

Power off

Blue indicator off

Power on

Blue indicator on

Narrow-band Tx / Rx Indicator

Host Status

Narrow-band Indicator Status

Flicker Period

Standby

Green indicator flickering

1.0s on, 5.0s off

Call

Red indicator normally on

Receive voice

Green indicator normally on

Status of LAN indicator

Host Status

Broadband Indicator Status

Flicker Period

Network searching

Green indicator flickers slowly

1.0s on, 1.5s off

Network connected

Green indicator flickers

quickly

0.1s on, 1.5s off

Call

Red indicator normally on

Receive voice

Green indicator normally on

Backup Battery Indicator (Optional)



Battery indicator is off when backup battery is not installed.



Battery indicator is normally on in red when backup battery is installed and the Product is

being charged.



Battery indicator is normally on (green) when backup battery is installed and the Product is

charged.



Battery indicator is normally on (green) after charging.

Summary of Contents for CONVERGENCE




















Search results

Summary of Contents for CONVERGENCE

Reviews:

Related manuals for CONVERGENCE

Brands by name

Popular brands

Auctus CONVERGENCE, User Manual

Search results

Summary of Contents for CONVERGENCE

Reviews:

Related manuals for CONVERGENCE

Brands by name

Popular brands