manualshive.com logo in svg

ATX ChromaFlex DMT24, Hardware Interface Manual

Share
Download
ATX ChromaFlex DMT24 Hardware Interface Manual Download Page 19

MODULE INSTALLATION 

ChromaFlex DMT24, DMT34 & DMT44 Multi-Wavelength DWDM Direct Modulated Transmitter Module  – Hardware Interface Manual 

7-1

MODULE INSTALLATION

7 .  Module Installation 

The DMTx4 (x=2, 3 or 4) transmitter module occupies a single ChromaFlex chassis module slot. The modules may be 

inserted or removed while the chassis is powered without interrupting other operational modules in the chassis. The 

following module installation procedures assume the chassis is installed and powered following the instructions in the 

ChromaFlex Operation Manual.

1.  Align the module into the desired slot opening in the ChromaFlex chassis.
2.  Using the handle push the module into the slot with even pressure until the module is mated with the chassis mid-

plane connector. 

3.  Press the module extraction levers downward against the module face.
4.  Tighten the two module retaining screws until snug in an even manner.
5.  The module LEDs should now be lit with the four OPT LEDs green and the four RF LEDs red (DMT44) if RF has not 

already been connected to the chassis rear panel RF connectors. 

CHAPTER 7: 

Summary of Contents for ChromaFlex DMT24

































Reviews:

No comments

Brands by name

Popular brands

Load more brands