ATTO Technology FastStream NDMP 4600, Installation And Operation Manual

Page: 45 / 58

38
Interfaces: CLI
ReadOnlyPassword
Specifies a read only password for all sessions: TCP/IP,
FTP and ExpressNAV web-based interface. You are
prompted for the current password, to enter the new
password, and to confirm the new password. Passwords
are case sensitive, 0-32 characters with no spaces.An
empty password can be configured by entering the
Password confirmation prompts with no parameters. The
command
RestoreConfiguration default sets the
password to its default value.
Default: Password
set ReadOnlyPassword
Requires a SaveConfiguration command
ReadOnlyUsername
Specifies a read only user name for all TCP/IP, FTP and
ExpressNAV web server sessions. User name is case
insensitive, 1-32 characters with no spaces.
Default: user
set ReadOnlyUsername [username]
Requires a SaveConfiguration command
get Username
RMON
RMON collects and stores Ethernet data on data ports at
specified intervals. You can display the entire table
requested, or a single entry based on the index (and
sample index for the Ethernet History table).
Entries in the Ethernet History table are not valid when
the Sample Index is 0.
Setting the history control entries take effect immediately,
but changes must be saved to be persistent over a reboot.
Valid range for EthernetStat index: 1-3
Valid range for historyControl & EthernetHistory
index:1-6
Valid range for historyControl buckets requested:1-
180
Valid range for historyControl interval: 1-3600
Default historyControl table (buckets and interval in
hexadecimal)
Default: Refer to Exhibit 5.1-7
set RMON [idx] [bucketsRequest] [interval] [valid | invalid]
Usage for entire table: get RMON [ethernetStat |
historyControl] <idx>
Usage for single index entry: get RMON ethernetHistory
<idx sampleIdx>
Username
Specifies a user name for all TCP/IP, FTP and
ExpressNAV web server sessions. User name is case
insensitive, 1-32 characters with no spaces.Changes to
the Admin Level User name require an Admin Level
password.
Default: root
set Username [username]
Requires entering a password
Requires a SaveConfiguration command
get Username
VLAN
Creates up to eight Virtual LAN IDs for each Ethernet
data port. Each VLAN ID is assigned a VLAN name of up
to 64 characters. If no VLALN ID exists for a data port,
VLAN is disabled for that port.Refer to
Set up a VLAN:
Virtual Local Area Network on page 12
set VLAN [DPn] [[VLAN ID] [VLAN Name] <delete>| [all]
[delete]]
Requires a SaveConfiguration command
get VLAN [DPn]
Exhibit 5.1-7 Default history Control table (buckets and interval in hexadecimal) for the RMON CLI
command.
Idx DataSrc BktReq BktGrant Interval Owner Status
====================================================================
001 43.6.1.2.1.2.2.1.1.1 00000032 00000032 0000001e monitor 00000004
002 43.6.1.2.1.2.2.1.1.1 00000032 00000032 00000708 monitor 00000004
003 43.6.1.2.1.2.2.1.1.2 00000032 00000032 0000001e monitor 00000004
004 43.6.1.2.1.2.2.1.1.2 00000032 00000032 00000708 monitor 00000004
005 43.6.1.2.1.2.2.1.1.3 00000032 00000032 0000001e monitor 00000004
006 43.6.1.2.1.2.2.1.1.3 00000032 00000032 00000708 monitor 00000004