background image

All rights reserved. No part of this manual may be reproduced or transmitted in any form by any means, electronic, 

mechanical, photocopying, recording, or otherwise, without the prior written permission of Atomik™. For information on 

getting permission for reprints and excerpts, contact [email protected].

The information in this manual is distributed on an “As Is” basis, without warranty. While every precaution has been 

taken in the preparation of the manual, Atomik™ does not have any liability to any person or entity with respect to any 

loss or damage caused or alleged to be caused directly or indirectly by the information contained in this manual or by 

the products described in it.

Charging and discharging batteries has the potential for serious injury to persons and damage to property. In purchasing 

this product, the user agrees to accept responsibility for all such risks, and will not hold Atomik™, it’s affiliates, 

manufacturers, distributors, or retail partners responsible for any accident, injury to persons, or damage to property 

resulting from the use of this product. This product contains chemicals known to the State of California to cause cancer, 

birth defects and other reproductive harm. Be responsible, dispose of properly.

FCC Warning:

CAUTION:   Atomik™ is not responsible for any radio or TV interference caused by unauthorized modifications to this 

product. Changes or modifications not authorized by Atomik™ will void all warranties.

NOTE:  This product has been tested and found to comply with the limits for a Class B digital device, compliant to Part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and 

used as instructed, may cause harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this product does cause harmful interference to radio or television 

reception, which can be determined by turning the product on and off, correct the interference by trying one or more of 

the following measures:

-  Reorient or relocate the receiving antenna.

-  Increase the separation between the equipment and receiver.

-  Connect the equipment into an outlet on a circuit different from the receiver.

-  Consult the dealer or an experienced radio/TV technician for help.

General Warranty Policies

Atomik™ warrants this product to be free of material and workmanship defects when new. Atomik™ will, at its sole 

discretion, repair or replace defective components free of charge within 90 days from date of purchase or within 30 

days for all electronic components.  This warranty does not cover wear and tear, crash damage, modifications, failure 

to perform routine maintenance, or any damages arising as a result of improper use. All warranty claims are to be 

directed to Atomik™ Customer Service at 1-800-705-0620 (208-762-0620) or [email protected].

Do not hold the back of the boat when launching. The propeller is very sharp and may cause severe injury. Always 

disconnect the battery when working on the boat to avoid electric shock. Be very careful, these boats are capable of 

reaching high speeds. Make sure you have plenty of open space to run your model.   

Important Notice

Atomik™ assumes sole responsibility for our products; therefore, dealers should not be involved in any warranty 

issues.  All warranty claims are to be directed to Atomik™ Customer Service. Before returning any defective product, 

please contact Atomik™ Customer Service at 800-705-0620 (208-762-0620) or [email protected] to 

receive a Return Merchandise Authorization Number.  A dated & itemized sales receipt must accompany any product 

returned for warranty work.

GUARANTEE

All products are inspected and adjusted individually before leaving the manufacturer and are guaranteed to be free of 

material defects and manufacturing faults. 

18

WARNINGS

Problem

Cause

Fix

Speed Control does not operate.

1. Transmitter and/or receiver is not switched on.

1. Switch on

2. Batteries are not fully charged.

2. Charge batteries

3. Improper radio installation.

3. Reinstall correctly

Motor does not operate.

1. Batteries are not fully charged.

1. Charge batteries

2. Improper radio installation.

2. Reinstall correctly

3. Loose motor wire connection.

3. Check connections

4. Damaged motor.

4. Replace or repair

1. Flex shaft and/or bearings are dirty.

1. Clean and regrease

Motor rotates, but boat does not move.

Propeller does not rotate freely when 

disconnected from the motor.

1. Motor coupler set screw is loose.

1. Tighten set screw

 T

 T

TROUBLE SHOOTING

Summary of Contents for A.R.C. C1





















Reviews: