Atmel RCB256RFR2 Hardware User Manual Download | Manualshive

Page: 7 / 35

background image

Atmel AVR10004: RCB256RFR2 – Hardware User Manual [APPLICATION NOTE]

7

3.3

Application (base) board connectors

Figure 3-3. Application board connector drawing.

The drawing in

shows the connector to be used on a base board to interface the RCB EXT0/1 connectors.

The detailed part number is: TFM-115-02-S-D.

Alternatively, a Tyco part can be used: Tyco 5-104655-4.

Note:

The Tyco part requires a different footprint design!

The drawing shown in

is from a SAMTEC datasheet. Check the latest datasheet for possible updates and

changes.

«
...
5
6
7
8
9
...
»

Summary of Contents for RCB256RFR2




































Reviews:

No comments

Related manuals for RCB256RFR2

Brand: Hama Pages: 12

Brand: TP-Link Pages: 2

Scorpio WD2500BPVT

Brand: Western Digital Pages: 3

Scorpio WD2500BPVT

Brand: Western Digital Pages: 4

Brand: Commell Pages: 9

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: Vecow Pages: 61

Brand: Lindy Pages: 12

Brand: Doremi Pages: 15

Brand: Xantech Pages: 16

SFD-2 MkIII Jumper

Brand: Anthem Audio Pages: 2

Brand: Konica Minolta Pages: 31

Masterliquid ML240L RGB

Brand: Cooler Master Pages: 18

Brand: Magewell Pages: 10

Brand: Z3 Technology Pages: 18

Brand: Keithley Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands