Headquarters
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
TEL 1 (408) 441-0311
FAx 1 (408) 487-2600
International
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
TEL (852) 2721-9778
FAx (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 St.-Quentin-en-Yvelines
Cedex, France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
TEL (81) 3-3523-3551
FAx (81) 3-3523-7581
Product Contacts
Technical Support
www.atmel.com/products/AT91CAP
Sales Contacts
www.atmel.com/contacts
Web Site
www.atmel.com
© 2008 Atmel Corporation.
All rights reserved.
Atmel
®
, logo and combinations thereof,
and others, are registered trademarks,
CAP™ and others are trademarks of
Atmel Corporation or its subsidiaries.
ARM
®
and ARM7TDMI
®
are registered
trademarks of ARM Ltd. Other terms
and product names may be trademarks
of others.
REV.: 8522A-03/08
Disclaimer:
The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with
the sale of Atmel products. ExCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY ExPRESS, IMPLIED OR
STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL
ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the
accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications
intended to support or sustain life.
AT91CAP7X-DK Development Kit
for CAP Customizable Microcontroller
The CAP Customizable Microcontroller
Atmel’s CAP is an ARM microcontroller-based system-on-chip with fast local memory, a wide range
of industry standard peripherals and interfaces, and a Metal Programmable (MP) Block that allows the
designer to add custom logic. By combining the performance, density and low power consumption of
the fixed portion of the device with the flexibility of the MP Block, CAP enables application-specific
products to be developed in a fraction of the time and at a fraction of the cost of standard-cell ASICs,
but at a unit price close to that of standard cell devices. CAP also offers superior performance, smaller
form factor and lower power consumption at a unit price significantly lower than an MCU-plus-FPGA
combination for the same functionality.
AT91CAP7X Features
n
160 KB of fast on-chip SRAM
n
A large MP Block of 450K ASIC gates (2-input NAND equivalents)
n
Micro Core = ARM7TDMI
®
at 80 MHz
n
MPRAM = 2x DPRAM 2K x 16
n
ROM = 256 KB
n
A minimal number of ARM peripherals are instantiated in the fixed portion
of the design to address low cost applications
n
Flexibility to instantiate other peripherals in the MP Block using IP
available in Atmel's vast library
