manualshive.com logo in svg

Atmel AVR AT90CAN128, Manual

The Atmel AVR AT90CAN128 is a versatile microcontroller perfect for automotive and industrial applications. For a comprehensive understanding of its features and capabilities, download the free user manual from manualshive.com. The manual provides detailed instructions and insights for smooth operation and development with the AT90CAN128.

Share
Download
background image

110

7679H–CAN–08/08

AT90CAN32/64/128

• Bit 6, 3 – WGM01:0: Waveform Generation Mode

These bits control the counting sequence of the counter, the source for the maximum (TOP)
counter value, and what type of waveform generation to be used. Modes of operation supported
by the Timer/Counter unit are: Normal mode, Clear Timer on Compare match (CTC) mode, and
two types of Pulse Width Modulation (PWM) modes. See 

Table 12-1

 and 

“Modes of Operation”

on page 104

.

Note:

1. The CTC0 and PWM0 bit definition names are now obsolete. Use the WGM01:0 definitions. 

However, the functionality and location of these bits are compatible with previous versions of 
the timer.

• Bit 5:4 – COM01:0: Compare Match Output Mode

These bits control the Output Compare pin (OC0A) behavior. If one or both of the COM0A1:0
bits are set, the OC0A output overrides the normal port functionality of the I/O pin it is connected
to. However, note that the Data Direction Register (DDR) bit corresponding to the OC0A pin
must be set in order to enable the output driver.

When OC0A is connected to the pin, the function of the COM0A1:0 bits depends on the
WGM01:0 bit setting. 

Table 12-2

 shows the COM0A1:0 bit functionality when the WGM01:0 bits

are set to a normal or CTC mode (non-PWM).

Table 12-3

 shows the COM0A1:0 bit functionality when the WGM01:0 bits are set to fast PWM

mode.

Table 12-1.

Waveform Generation Mode Bit Description

(1)

Mode

WGM01

(CTC0)

WGM00
(PWM0)

Timer/Counter
Mode of Operation

TOP

Update of 
OCR0A at

TOV0 Flag
Set on

0

0

0

Normal

0xFF

Immediate

MAX

1

0

1

PWM, Phase Correct

0xFF

TOP

BOTTOM

2

1

0

CTC

OCR0A

Immediate

MAX

3

1

1

Fast PWM

0xFF

TOP

MAX

Table 12-2.

Compare Output Mode, non-PWM Mode

COM0A1

COM0A0

Description

0

0

Normal port operation, OC0A disconnected.

0

1

Toggle OC0A on compare match

1

0

Clear OC0A on compare match

1

1

Set OC0A on compare match

Table 12-3.

Compare Output Mode, Fast PWM Mode

(1)

COM0A1

COM0A0

Description

0

0

Normal port operation, OC0A disconnected.

0

1

Reserved

1

0

Clear OC0A on compare match.

Set OC0A at TOP

1

1

Set OC0A on compare match.

Clear OC0A at TOP

Summary of Contents for AVR AT90CAN128













































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AVR AT90CAN128

ABB XFC G5 Quick Start Manual preview
XFC G5
Brand: ABB Pages: 2
ZKTeco PA10 Quick Start Manual preview
PA10
Brand: ZKTeco Pages: 8
EasyIO FT Series User Reference preview
FT Series
Brand: EasyIO Pages: 18
Nabco Opus Control Installation Manual preview
Opus Control
Brand: Nabco Pages: 35
Samson TROVIS 3730-1 Installation Instructions Manual preview
TROVIS 3730-1
Brand: Samson Pages: 6
Dahua DHI-ARC3008C User Manual preview
DHI-ARC3008C
Brand: Dahua Pages: 137
Parker 890CS Product Manual preview
890CS
Brand: Parker Pages: 478
Kampmann 197901960988 Manual preview
197901960988
Brand: Kampmann Pages: 5
Ascon tecnologic Y39 Operating Instructions Manual preview
Y39
Brand: Ascon tecnologic Pages: 16
KIOUR FA3F Quick Start Manual preview
FA3F
Brand: KIOUR Pages: 3
Encelium Wired Manager - DALI Installation Instructions Manual preview
Wired Manager - DALI
Brand: Encelium Pages: 8
Z-Wave Alliance SR-ZV9002T4-CCT-RU Manual preview
SR-ZV9002T4-CCT-RU
Brand: Z-Wave Alliance Pages: 10
Kustom Signals Eyewitness HD ICV System Quick Reference Manual preview
Eyewitness HD ICV System
Brand: Kustom Signals Pages: 4
Hanna Instruments BL121 Manual preview
BL121
Brand: Hanna Instruments Pages: 44
ETI PFC 12 RS User And Service Manual preview
PFC 12 RS
Brand: ETI Pages: 14
WAGO 750-8202/040-000 Manual preview
750-8202/040-000
Brand: WAGO Pages: 418
Teradek CTRL.1 Quick Start Manual preview
CTRL.1
Brand: Teradek Pages: 10
X10 SC503 Owner'S Manual preview
SC503
Brand: X10 Pages: 3

Brands by name

Popular brands

Load more brands