Atmel AT32UC3C0128C Manual Download Page 1

Page: 1 / 37

Features

•

USB DFU boot loaders, version 1.1.0

•

Same feature set as version 1.0.3

•

These boot loaders do not use any general purpose fuses

•

USB protocol

– Based on the USB device firmware upgrade (DFU) class
– Auto-baud (8, 12, and 16MHz crystal on Osc0)

•

In-system programming (ISP)

– Configurable I/O start conditions (default is pressing the joystick on

Atmel

EVK1100

and

Atmel EVK1101

, SW2 button on

Atmel EVK1104

, PB0 button on

Atmel UC3C-EK, HBUTTON0 button on Atmel UC3-C2-Xplained board

) stored in

user page. Protected by 8-bit CRC

– Can be forced by non-volatile configuration bits stored in user page. Protected by

8-bit CRC

– Read/write, on-chip flash memories
– Read device ID
– Full chip erase
– Start application command

32166A–AVR32806–06/11

Atmel UC3 32-bit
Microcontroller

AVR UC3

USB

DFU Boot
Loader, Version
1.1.0 and Higher

Summary of Contents for AT32UC3C0128C






































Search results

Summary of Contents for AT32UC3C0128C

Reviews:

Related manuals for AT32UC3C0128C

Brands by name

Popular brands

Atmel AT32UC3C0128C, Manual

Search results

Summary of Contents for AT32UC3C0128C

Reviews:

Related manuals for AT32UC3C0128C

Brands by name

Popular brands