background image

AT-VCC-RELAY

4

Atlona, Inc. (“Atlona”) Limited Product 

Warranty

Coverage

Atlona warrants its products will substantially perform to their published specifications and will be free from defects 

in materials and workmanship under normal use, conditions and service.

Under its Limited Product Warranty, Atlona, at its sole discretion, will either:

• 

repair or facilitate the repair of defective products within a reasonable period of time, restore products to their 

proper operating condition and return defective products free of any charge for necessary parts, labor and 

shipping.

OR

•  replace and return, free of charge, any defective products with direct replacement or with similar products 

deemed by Atlona to perform substantially the same function as the original products.

OR

• 

refund the pro-rated value  based on the remaining term of the warranty period, not to exceed MSRP, in cases 

where products are beyond repair and/or no direct or substantially similar replacement products exist.

Repair, replacement or refund of Atlona products is the purchaser’s exclusive remedy and Atlona liability does not 

extend to any other damages, incidental, consequential or otherwise.

This Limited Product Warranty extends to the original end-user purchaser of Atlona products and is non-transferrable 

to any subsequent purchaser(s) or owner(s) of these products.

 

Coverage Periods

Atlona Limited Product Warranty Period begins on the date of purchase by the end-purchaser. The date contained on 

the end-purchaser ‘s sales or delivery receipt is the proof purchase date.

Limited Product Warranty Terms – New Products

•  10 years from proof of purchase date for hardware/electronics products purchased on or after June 1, 2013.
• 

3 years from proof of purchase date for hardware/electronics products purchased before June 1, 2013.

• 

Lifetime Limited Product Warranty for all cable products.

Limited Product Warranty Terms – Refurbished (B-Stock) Products

• 

3 years from proof of purchase date for all Refurbished (B-Stock) hardware and electronic products purchased 

on or after June 1, 2013.

Remedy

Atlona recommends that end-purchasers contact their authorized Atlona dealer or reseller from whom they  

purchased their products.  Atlona can also be contacted directly. Visit www.atlona.com for Atlona’s contact 

information and hours of operation. Atlona requires that a dated sales or delivery receipt from an authorized dealer,  

reseller or end-purchaser is provided before Atlona extends its warranty services. Additionally, a return merchandise 

authorization (RMA) and/or case number, is required to be obtained from Atlona in advance of returns.
Atlona requires that products returned are properly packed, preferably in the original carton, for shipping. Cartons not 

bearing a return authorization or case number will be refused. Atlona, at its sole discretion, reserves the right to reject 

any products received without advanced authorization. Authorizations can be requested by calling 1-877-536-3976 

(US toll free) or 1-408- 962-0515 (US/international) or via Atlona’s website at www.atlona.com.

Exclusions

This Limited Product Warranty excludes:

• 

Damage, deterioration or malfunction caused by any alteration, modification, improper use, neglect, improper 

packaging or shipping (such claims must be presented to the carrier), lightning, power surges, or other acts of 

nature.

Summary of Contents for AT-VCC-RELAY























Reviews: