background image

Installation 

21

PV-15P

Installation

Only skilled technicians, appointed by the manufacturer, or by 

authorized dealers, must be allowed to carry out installation. 

Serious damage to people and to the lift can be caused if 

installations are made by unskilled personnel.

Always refer to the exploded views attached during installation.

7.1 Tool 

Required

Rotary Hammer Drill D.19

Hex-Key/Allen Wrench Set

Masonry Bit

Crow Bar For Shim Installation

Hammer

Chalk Line

Level

Medium Cross Screwdriver

Open-End Wrench Set

Medium Flat Screwdriver

Medium Crescent Wrench

Tape Measure

7.2  Checking For Room Suitability

The lift has been designed to be used in covered and sheltered places free of 

overhead obstructions.

The place of installation must not be next to washing areas, painting 

workbenches, solvent or varnish deposits. The installation near to rooms, where 

a dangerous situation of explosion can occur, is strictly forbidden. The relevant 

standards of the local Health and Safety at Work regulations, for instance, with 

respect to minimum distance to wall or other equipment, escapes and the like, 

must be observed.

7.3 Lighting

Lighting must be carried out according to the effective regulations of the place of 

installation. All areas next to the lift must be well and uniformly lit.

Summary of Contents for PV-15PX






















































Reviews: