manualshive.com logo in svg

Atlas H151, Owner'S Manual, Page: 16 / 24

Share
Download
Atlas H151 Owner'S Manual Download Page 16

1 6 |

P a g e

Operational Screens with UV Monitor Upgrade

On systems that have the UV sensor installed, the default screen shows the 

UV Intensity

. At any 

point during operation the user is able to scroll through the 

UV Intensity

, 

Lamp life remaining 

and 

QR Code

 screens by pressing the button located on the front of the controller.

UV Intensity (with UV Monitor Upgrade)

The UV Intensity screens display the level of UV light detected by the sensor. UV intensity can be 

affected by poor water quality, scaling on the quartz sleeve and/or sensor, lamp failure or lamp 

expiring. The following screens show the UV Intensity dropping.

Below 56%, the numbers and warning sign turn red and an audible chirp is given by the ballast 

every 15 seconds. Below 51%, the screen is solid red and a constant audible alarm is given. This 

alternates with a screen indicating “water may be unsafe for consumption”. With the solenoid 

module, the controller de-activates the solenoid valve, shutting off all water flow.

Summary of Contents for H151

























Reviews:

No comments