Atlas Copco XAS 185 KDU T4F HOP Instruction Manual Download Page 53

Page: 53 / 62

- 53 -

Problem: After working some time, the unit stops through a shutdown switch.

Problem: Air and oil mist expelles from air filters immediately after stopping.

Problem: Compressor overheating.

Possible faults

Corrective actions

Engine oil pressure too low.

Refer to the engine instruction manual.

Compressor or engine overheating.

See corrective actions “Compressor overheating”.

Fuel tank contains insufficient fuel.

Fill fuel tank.

Low coolant level.

Top up cooling system.

Possible faults

Corrective actions

Check valve at element outlet.

Remove and inspect. Replace if necessary. Replace air filter elements and safety cartridges. Check the oil level

and add oil if necessary. Run the compressor for a few minutes, stop and recheck oil level.

Possible faults

Corrective actions

Insufficient compressor cooling.

Locate compressor away from walls; when banked with other compressors, leave space between them.

Oil cooler clogged externally.

Clean oil cooler. Refer to section Cleaning Coolers.

Oil cooler clogged internally.

Consult Atlas copco.

Oil filters clogged.

Replace oil filters.

Oil level too low.

Check oil level. Top up with recommended oil if necessary.

Thermostatic by-pass valve remains stuck in open position.

Remove valve and check for proper opening and closing. Replace if out of order.

Fan blade(s) broken.

Check and correct if necessary.

Oil separator element (OS) clogged.

Have element removed and inspected by an Atlas copco Service representative.

Summary of Contents for XAS 185 KDU T4F HOP































































Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews:

Brands by name

Popular brands

Atlas Copco XAS 185 KDU T4F HOP, Instruction Manual

Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews:

Brands by name

Popular brands