Atlas Copco XAS 185 KDU T4F HOP Instruction Manual Download Page 42

Page: 42 / 62

- 42 -

Details of ECU triggered alarms can be monitored via the ECU DM1 LIST menu

In case of ECU AMBER LAMP or ECU PROTECT LAMP:

Only possible when engine is running or if Diagnostics

Mode is active.

Access the ECU DM1 LIST menu via Alarm View.

In case of ECU RED LAMP:

Do NOT acknowledge the ECU RED LAMP alarm.

DM1 alarms are automatically copied into the Alarm

View, and can be read there.

For all ECU triggered alarms, the respective SPN code is

shown in the ECU DM1 LIST

A full list of supported SPN codes is provided by the engine

manufacturer.

For following alarms, the Xc controller also shows full text

next to the SPN code:

ECU - FUEL FILTER PRESSURE

ECU - INTERCOOLER TEMPERATURE

ECU - FUEL PRESSURE

ECU - FUEL FILTER PRESSURE

ECU - WATER IN FUEL

ECU - OIL LEVEL

ECU - OIL FILTER PRESSURE

ECU - OIL PRESSURE

ECU - TURBO BOOST PRESSURE

ECU - TURBO OIL PRESSURE

ECU - INTAKE MANIFOLD TEMPERATURE

ECU - AIR INLET PRESSURE

ECU - COOLANT TEMPERATURE

ECU - COOLANT LEVEL

ECU - SUPPLY VOLTAGE

ECU - AMBIENT AIR TEMPERATURE

ECU - AIR INLET TEMPERATURE

ECU - FUEL TEMPERATURE

ECU - OIL TEMPERATURE

ECU - ENGINE SPEED

ECU - INJECTOR 1

ECU - INJECTOR 2

ECU - INJECTOR 3

ECU - INJECTOR 4

ECU - INJECTOR 5

ECU - INJECTOR 6

ECU - INJECTOR 7

ECU - INJECTOR 8

ECU - SOOT LOAD

7100

ECU DPF SOOT LOAD HIGH

Warning

7110

PLEASE FORCE DPF REGENERATION

Inhibit Load

7120

LOAD PREVENTION - HIGH DPF SOOT LOAD

Controlled Stop

7130

SOOT LOAD TOO HIGH - CALL ATLAS COPCO

Warning

7222

COMBO COMMUNICATION FAILURE

Warning

7223

COMBO PA SENSOR WARNING

Warning

7224

COMBO RHA SENSOR WARNING

Warning

7225

COMBO TA SENSOR WARNING

Warning

Alarm code

Alarm text

Fail class

Trigger

Summary of Contents for XAS 185 KDU T4F HOP































































Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews:

Atlas Copco XAS 185 KDU T4F HOP, Instruction Manual, Page: 42 / 62

Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews: