manualshive.com logo in svg

Atlas Copco XAHS 347 CD, Instruction Manual

Share
Download
Atlas Copco XAHS 347 CD Instruction Manual Download Page 65

- 65 -

BRAKE CABLE ADJUSTMENT

Hand brake lever downward - brake not operated (adjustable
towbar)

Hand brake lever downward - brake not operated (fixed
towbar)

Brake cable arrangement

1. With the towing eye pulled out in the outmost 

position and the hand brake lever in the downward 
position, loosen the lock nuts (1). Turn the 
adjusting nuts and the brake cable nuts (2) 
clockwise until there is no slack in the brake 
mechanism. The equalizer (3) must remain 
perpendicular to the main brake cable (4).

2. Apply the hand brake lever several times and 

repeat the adjustment. Tighten the nuts with their 
lock nuts (1). Remove the jack and the blocks.

3. Road test the compressor and brake several times. 

Check the brake shoe and the brake cable 
adjustment and if necessary adjust.

TEST PROCEDURE OF BRAKE CABLE 
ADJUSTMENT

1. Pull main brake cable downwards.

2. The brake cables need 3 mm (0.12 in) to 5 mm 

(0.2 in) margin (to see on different colors on 
cables from grease/dust).

(1)

(1)

(2)

(3)

(4)

3 mm - 5 mm

Summary of Contents for XAHS 347 CD

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands