Atlas Copco Tensor Quick Manual Download Page 14

Page: 14 / 14

www.atlascopco.com

Error

code

Description

Ack-

now-

ledge

What to do?

Help

text

E403

IO device not
responding

Check cables and restart drive.

E408

Multiple devices
of same type on
IO bus

Yes

You are only allowed to use one.

E409

Multiple selectors
on IO bus

Yes

E410

No selector
found and pset
source is IO bus

Yes

Connect the Selector and restart
the drive or choose None
on Selector Source in TTDS/
Configuration.

E412

IO expander has
ID <> 2

Yes

E413

RE Alarm has ID
<> 3

Yes

E415

4 socket selector
has ID <> 5

Yes

E416

8 socket selector
has ID <> 6

Yes

E501 Tool overheated

Let the tool cool down and restart.

E502 Service Indicator

Yes

Service the tool.

E517

Tool maxtorque
or Gear Ratio out
of range

Yes

Check tool memory.

E601 Dcbus LO

Yes

Restart drive. If problem still
remains check line voltage.

E602 Dcbus HI

Yes

Restart drive. If problem still
remains check line voltage.

ERROR CODES

9833

424

tta.45 Tryckeri AB

08:

Summary of Contents for Tensor















Search results

Summary of Contents for Tensor

Reviews:

Related manuals for Tensor

Brands by name

Popular brands

Atlas Copco Tensor, Quick Manual

Search results

Summary of Contents for Tensor

Reviews:

Related manuals for Tensor

Brands by name

Popular brands