Safety Information
ETP SRB31-20-I06-BD
4
© Atlas Copco Industrial Technique AB - 9834 5622 00
• Be done after initial installation, maintenance or repair
of the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF CONFORMITY
We,
Atlas Copco Industrial Technique AB
, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that the product (with name, type and serial number,
see front page) is in conformity with the following Direc-
tive(s):
2006/42/EC (MD), 2011/65/EU (RoHS), 2014/53/EU
(RED), 2015/863/EU (RoHS amendment)
Harmonized standards applied:
EN 300 440 V2.1.1, EN 301 893 V2.1.1, EN 301489-1
V2.1.1, EN 301489-17 V3.1.1, EN 50566:2017, EN
55014-1:2017, EN 55014-2:2015, EN 61000-6-1:2007, EN
61000-6-2:2005, EN 61000-6-3:2007+A1, EN
61000-6-4:2007+A1, EN 62841-1:2015, EN
62841-2-2:2015+AC1, EN 300 328 V2.2.2
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Tech-
nique AB, SE-105 23 Stockholm Sweden
Stockholm, 1 December 2021
Carl von Schantz, Managing Director
Signature of issuer
Noise and Vibration Declaration Statement
• Sound pressure level <70 dB(A) , uncertainty 3 dB(A),
in accordance with ISO15744.
• Sound power level <80 dB(A) , uncertainty 3 dB(A), in
accordance with ISO15744.
• Vibration total value <2,5 m/s
2
, uncertainty - m/s
2
, in ac-
cordance with ISO28927-2.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We,
Atlas Copco Industrial Technique AB
, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
and selecting 'Tools' then 'Legis-
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
Noise and Vibration Declaration Statement
using TensorPulse strategy
• Sound pressure level 75 dB(A), uncertainty 3 dB(A), in
accordance with ISO15744.
• Sound power level dB(A) , uncertainty 3 dB(A), in ac-
cordance with ISO15744.
• Vibration value 9,5 m/s
2
, uncertainty 1,3 m/s
2
, in accor-
dance with ISO28927-2.
This tool may cause hand-arm vibration syndrome if its
use is not adequately managed.
Recommended working
hours are calculated by using the Vibration Exposure Calcu-
lator:
Click here to go to Calculator
rotation to reduce vibration exposure.
WEEE
Information concerning
Waste of Electrical and Electronic
Equipment
(WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE Directive. The entire
product, or the WEEE parts, can be sent to your “Customer
Center” for handling.
Conformity to North American Standards
3008099
Listed
Conforms to UL 62841-1 and
UL 62841-2-2 Std.
Certified to CSA C22.2 No.
62841-1 and CSA C22.2 No.
62841-2-2 Std.
