Atkinson Electronics A0217 Manual Download Page 16

www.atkinsonelectronics.com 

             Circuit Board Division 

800.261.3602 

16 

Revised 09/18

 

 

GSCM Limited Warranty 

 

Atkinson Electronics, Inc. gives this express warranty (along with extended warranty endorsements, where applicable) in lieu of 
all other warranties, express or implied, including (without limitation), warranties of merchantability and fitness for a particular 
purpose. This constitutes Atkinson Electronics, Inc.'s sole warranty and obligation with regard to our products as well as the 
Customer's sole remedy. 
Atkinson Electronics, Inc. expressly disclaims all liability and responsibility for any special, indirect or consequential damages or 
any further loss of any kind whatsoever resulting from the use of our product. The Customer's sole and exclusive remedy and 
the limit of Atkinson Electronics, Inc.'s liability for any loss whatsoever, shall not exceed the purchase price paid by the Customer 
for the product to which a claim is made. 
Countries or States that do not allow limitations of incidental or consequential damages or on how long an implied warranty 
lasts, the above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights 
which vary from State to State or Country to Country. 
All products manufactured by Atkinson Electronics, Inc. are warranted to be free from defects in material and workmanship in 
accordance with and subject to the following terms and conditions: 
 

1.

 

This warranty is limited to the original customer only.  It cannot be transferred or assigned to third parties unless the 
intent to transfer to a third party is expressly indicated in a purchase order and/ or warranty processing arrangements 
have been agreed upon in writing by Atkinson Electronics, Inc. 

2.

 

Atkinson Electronics, Inc. will correct any defects in material or workmanship which appear within two (2) years from 
the date of shipment by Atkinson Electronics, Inc. (or its authorized distributors) to the original Customer.  Atkinson 
Electronics, Inc. will repair or replace, at our option, any defective products, provided that our inspection discloses that 
such defects developed under normal and proper use.  This warranty does not extend to goods subjected to misuse, 
neglect, accident or improper installation, or to maintenance or repair of products which have been altered or repaired 
by anyone except Atkinson Electronics, Inc., unless otherwise stated in writing.  Atkinson Electronics, Inc. will correct 
any defects in material or workmanship of OEM products (designated as such in our catalog or web site) which appear 
within two (2) years from the product date code or from the factory invoice date, whichever is later. 

3.

 

An appropriate charge (25% of product list price) may be made for testing, repairs, replacement and shipping for a 
returned product which is not defective or found to be defective as the result of improper use, maintenance or neglect. 

4.

 

Atkinson Electronics, Inc. will not accept responsibility for any invoiced goods or services that are not covered by an 
Atkinson Electronics, Inc. written purchase order.  Under no circumstances does Atkinson Electronics, Inc. agree to pay 
for labor or other related expenses associated with the troubleshooting and/ or repair of our product without prior 
specific written authorization. 

5.

 

 Information in our descriptive literature is based on product specifications that are current at the time of publication. 

Product specifications, design and descriptive literature are subject to change as improvements are introduced.  Although we 
announce changes as they occur, we cannot guarantee notification to every Customer.  Atkinson Electronics, Inc. warrants 
delivered products to conform to the most current specifications, design and descriptive literature.  This warranty policy may 
be expanded or limited, for particular categories of products or Customers, by information sheets published as deemed 
appropriate by Atkinson Electronics, Inc. 

Summary of Contents for A0217

















Reviews: