13
S
S
a
a
f
f
e
e
w
w
o
o
r
r
k
k
i
i
n
n
g
g
Before commissioning this product, read and keep
to the following advice. Also observe the preventive
regulations of your professional association and the
safety provisions applicable in the respective country, in
order to protect yourself and others from possible injury.
L
Pass the safety instructions on to all persons who
work with the machine.
L
Keep these safety instructions in a safe place.
Repairs on the safety cut-out must be done by the
producer or by a company designated by the
producer.
Make yourself familiar with the equipment before using it,
by reading and understanding the operating instructions.
Do not use the machine for unsuitable purposes (see
“Normal intended use” and “Working with the garden
shredder”').
Ensure that you have stand in a
secure standing
position
and maintain your
balance
at all times. Do not
lean forward over the machine. When placing material
into the chopper, always
stand on the same level
as the
machine.
Be
attentive
. Be careful what you do. Behave
sensibly
when working. Do
not
use the saw if you are
tired
.
Wear protective goggles, gloves and noise protection
while working
with the machine.
Wear suitable
work clothes
!
−
Do not wear loose-fitting clothes
−
Slip-proof
shoes
•
Within his area of work
the operator
is responsible for
third parties.
•
The machine must not be operated by
children or young
people under 16 years of age
.
Keep
children
away form machine.
Never operate the machine if
other persons are in the
immediate vicinity
.
Never
leave the machine
unattended.
Keep your
workplace in an orderly condition
!
Untidiness can result in accidents.
Choose a
working
position
alongside the equipment or
behind it. Never stand near the ejection opening.
Never
reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Do not overload the machine! You work better and safer
in the
given performance range.
Only operate the machine with complete and correctly
attached
safety equipment
and do not alter anything on
the machine that could impair the safety.
Do not alter the
revolution speed
of the motor, since this
controls the safe maximum operating speed, and protects
the motor and all rotating parts against damage due to
excess speed.
Do
not
operate
without the funnel
.
Faulty
or
damaged parts
in the device must be replaced
immediately.
Close machine properly before enabling motor.
Do
not spray machine with water
(this is hazardous due to live components).
Do
not
leave the machine
standing in the rain
or use
when raining.
Store the
unused machine
in a dry locked place away
from the reach of children.
To prevent danger of injury to fingers during assembly or
cleaning operations wear protecting gloves.
Switch the machine off and
remove the mains plug from
the socket
when
−
carrying out servicing and repair
works, removal of faults
−
carrying out repair works
−
transporting
−
leaving unattended (even during short interruptions)
Check the machine for possible damage
−
Before continuing to use the machine, the
protective
devices
must be inspected to ensure that they work
perfectly and with their intended function
−
Check whether the parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the saw
−
Damaged guards
and parts must be properly
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
−
Damaged or illegible
safety warning labels
should
be
replaced
immediately.
Electrical safety
Design of the
connection cable
according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
−
1.5 mm
2
for cable lengths
up to
25m
−
2.5 mm
2
for cable lengths
over
25m
When laying the
connecting attachments
, be sure that
they do get crushed or bent, and that the plug-and-socket
connection does not get wet.
Do not use the
cable
for purposes for which it is not
meant.
Protect
the cable against
heat, oil and sharp
edges
. Do not use the cable to pull the plug from the
socket.
Regularly check the
extension cables
and replace them
if they are damaged
Do
not use any defective connection cables
When working outdoors, only use extension cables espe-
cially
approved
and appropriately labelled for outdoor
use
Do
not set up any provisional
electrical connections.
Never bypass
protective devices or deactivate them.
Connect the machine using a fault
current protection
switch
(30 mA).
The
electrical connection
or
repairs
to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points. Local
regulations – especially regarding protective measures
– must be observed.
