background image

Page 15

To Erase a Learned Command

From a Button

Step 1.  Press the Device button and 

SELECT

buttons

simultaneously, and hold until the orange Status LED
and the Device button turn on and remain lit. 

Step 2.  On the remote control, press the button that is to be

erased. The orange Status LED will flash continuously
and the Device button will turn off.

Step 3.  Press the 

LIGHT

button. The green status LED will

flash twice, then turn to a steady orange. The
Device button will turn on.

Repeat from Step 2 for any other buttons to be erased in the
selected Device mode. 

Step 4.  To exit this feature, press and hold the Device button

and the SELECT button simultaneously, once again.
The orange Status LED will flash twice and then
turn off. The Device button will turn off. 

To Erase All the Learned Commands

In One Device Mode

Step 1.  Press the Device button and 

SELECT

buttons

simultaneously, and hold until orange Status LED
and the Device button turn on and remain lit. 

Step 2.  Press and hold the 

LIGHT

button. The red Status LED

will flash five times. Release the 

LIGHT

button. The

Status LED will then flash green twice and then the
Device button will turn off. The Status LED will go to
a constant orange indicating that all the learned
information on buttons in the Device mode have
been erased. The Device button will turn on.

Step 3.  To exit this feature, press and hold the Device

button and the 

SELECT

button simultaneously.

The orange Status LED will flash twice and then
turn off. The Device button will turn off.

To Erase All the Learned Commands

In All Device Modes

Warning: This procedure will erase all

learned commands on all buttons in the

CD, DVD, AUX, SAT, TV,VCR and CBL device modes.

Step 1.  Press and hold the 

TV

Device button and the 

LIGHT

button simultaneously. The red Status LED will flash
continuously. The Status LED will then flash green
once, orange once then turn off, indicating that all
of the learned commands on all of the Device
modes on the remote control have been erased.   

Volume Punch Through

The user can have the Audio Volume controls (

VOL 

VOL 

and 

MUTE

) operate in any of the eight Device modes. 

Step 1.  Press the Device and 

MUTE

buttons, simultaneously.

Step 2.  Press the 

VOL 

button.

Step 3.  Press the 

AVC

device button to select the type of

volume control you wish to operate in that mode.

Example: If you wish to have the AVC volume operate in the
DVD mode, press the 

DVD

Device button in Step 1. of the

instructions and the 

AVC

Device button in Step 3.

All manuals and user guides at all-guides.com

Summary of Contents for ATP 7500





















Reviews: