manualshive.com logo in svg

ATEN CS1308, User Manual

The ATEN CS1308 is a top-notch switch with advanced features and user-friendly design. To maximize its potential, make sure to refer to the comprehensive User Manual, available for free download at manualshive.com. This manual is essential for setting up and optimizing your ATEN CS1308 switch efficiently and hassle-free.

Share
Download
background image

CS1308 / CS1316 User Manual

44

4. Click 

Next

 to perform the upgrade.

If you enabled 

Check Firmware Version

, the Utility compares the device's 

firmware level with that of the upgrade files. If it finds that the device's 
version is higher than the upgrade version, it brings up a dialog box 
informing you of the situation and gives you the option to continue or 
cancel.

If you didn't enable 

Check Firmware Version

, the Utility installs the 

upgrade files without checking whether they are a higher level, or not.

As the upgrade proceeds, status messages appear in the 

Status Messages

 

panel, and the progress toward completion is shown on the 

Progress

 bar.

Summary of Contents for CS1308





































































Reviews:

No comments

Related manuals for CS1308

Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES How To Connect preview
LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES
Brand: Jabra Pages: 4
Murphy Temperature SWICHGAGE SPL Owner'S Manual preview
Temperature SWICHGAGE SPL
Brand: Murphy Pages: 4
DANLERS TLSW HB Installation Notes preview
TLSW HB
Brand: DANLERS Pages: 2
Dahua PFS3005-5ET-V2 Quick Start Manual preview
PFS3005-5ET-V2
Brand: Dahua Pages: 17
J-Tech Digital JTD-3003 User Manual preview
JTD-3003
Brand: J-Tech Digital Pages: 13
Kramer VS-24xl User Manual preview
VS-24xl
Brand: Kramer Pages: 11
N-Tron 708TX User Manual & Installation Manual preview
708TX
Brand: N-Tron Pages: 157
ALFAtron ALF-MUH88E User Manual preview
ALF-MUH88E
Brand: ALFAtron Pages: 44
Black Box LGB2118A-R2 Startup Manual preview
LGB2118A-R2
Brand: Black Box Pages: 20
IBM 8265 Nways ATM Switch Product Description preview
8265 Nways ATM Switch
Brand: IBM Pages: 100
Lindy 38148 User Manual preview
38148
Brand: Lindy Pages: 6
I-Tech CMS-6R4 User Manual preview
CMS-6R4
Brand: I-Tech Pages: 123
Bticino RW4003DCW Quick Start Manual preview
RW4003DCW
Brand: Bticino Pages: 2
ANTIFERENCE Clear Switch CF-POE8 User Manual preview
Clear Switch CF-POE8
Brand: ANTIFERENCE Pages: 7
BCXLAB LYNQ User Manual preview
LYNQ
Brand: BCXLAB Pages: 6
NETGEAR GS308P Installation preview
GS308P
Brand: NETGEAR Pages: 2
ATEN UC2322 User Manual preview
UC2322
Brand: ATEN Pages: 16
Radio Shack AFX-400 Owner'S Manual preview
AFX-400
Brand: Radio Shack Pages: 16

Brands by name

Popular brands

Load more brands